Cisco ASR 9000 Series 매뉴얼 - 페이지 36
{카테고리_이름} Cisco ASR 9000 Series에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco ASR 9000 Series 44 페이지. Line card
Cisco ASR 9000 Series에 대해서도 마찬가지입니다: 네트워크 설정 구성 (26 페이지), 구성 매뉴얼 (46 페이지), 구성 매뉴얼 (50 페이지), 매뉴얼 (24 페이지), 구성 (46 페이지), 빠른 참조 매뉴얼 (7 페이지)
페이지 인쇄
- 1. Field Replaceable Units
- 2. Online Insertion and Removal
- 3. Powering off the Router
- 4. Replacing the Chassis Air Filter
- 5. Required Tools and Equipment
- 6. Removing a Fan Tray
- 7. Installing a Fan Tray
- 8. Disconnecting AC Power
- 9. Reconnecting AC Power
- 10. Disconnecting DC Power
- 11. Reconnecting DC Power
Migrating from RSP4-S to RSP880-LT Card (ASR 9906 Router)
Migrating from RSP4-S to RSP880-LT Card (ASR 9906 Router)
Before you begin:
• You must have console access to the router.
• The router must be running Cisco IOS XR software release 6.3.2 or later version.
• The router must have two RSP4-S cards (active and standby) up and running.
• Set the MISMATCH_RP_ENABLED ROMMON variable to 1:
Procedure
Step 1
Enter the show redundancy summary command to identify the active and standby RSPs.
Example:
Router# show redundancy summary
Wed Jun 17 11:18:51.391 PST
Active/Primary Standby/Backup
-------------- --------------
0/RSP1/CPU0(A) 0/RSP0/CPU0(S) (Node Ready, NSR: Ready)
0/RSP1/CPU0(P) 0/RSP0/CPU0(B) (Proc Group Ready, NSR: Ready)
Step 2
Remove the standby RSP4-S from slot 0 and insert the RSP880-LT. Follow the procedure in
Replacing Cards from the Chassis, on page
Step 3
Wait until the standby node reaches NSR-ready state and the status of all groups is in Ready state. Enter the
show redundancy command to verify.
Example:
Router# show redundancy
Wed Jun 17 11:18:53.098 PST
Redundancy information for node 0/RSP1/CPU0:
==========================================
Node 0/RSP1/CPU0 is in ACTIVE role
Node Redundancy Partner (0/RSP0/CPU0) is in STANDBY role
Standby node in 0/RSP0/CPU0 is ready
Standby node in 0/RSP0/CPU0 is NSR-ready
Node 0/RSP1/CPU0 is in process group PRIMARY role
Process Redundancy Partner (0/RSP0/CPU0) is in BACKUP role
Backup node in 0/RSP0/CPU0 is ready
Backup node in 0/RSP0/CPU0 is NSR-ready
Group
---------
v6-routing
mcast-routing
netmgmt
v4-routing
Replacing Cisco ASR 9000 Series Router Components
36
1. Connect to the RSP4-S console port and press CTRL+C to break into ROMMON.
2. From the ROMMON prompt on the RSP4-S, set the ROMMON variable to allow mismatched RSP:
rommon B1> MISMATCH_RP_ENABLED=1
Primary
---------
0/RSP1/CPU0
0/RSP1/CPU0
0/RSP1/CPU0
0/RSP1/CPU0
Replacing Cisco ASR 9000 Series Router Components
25.
Backup
Status
---------
---------
0/RSP0/CPU0
Ready
0/RSP0/CPU0
Ready
0/RSP0/CPU0
Ready
0/RSP0/CPU0
Ready
Removing and