Cisco ASR 9000 Series 매뉴얼 - 페이지 38
{카테고리_이름} Cisco ASR 9000 Series에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco ASR 9000 Series 44 페이지. Line card
Cisco ASR 9000 Series에 대해서도 마찬가지입니다: 네트워크 설정 구성 (26 페이지), 구성 매뉴얼 (46 페이지), 구성 매뉴얼 (50 페이지), 매뉴얼 (24 페이지), 구성 (46 페이지), 빠른 참조 매뉴얼 (7 페이지)
페이지 인쇄
- 1. Field Replaceable Units
- 2. Online Insertion and Removal
- 3. Powering off the Router
- 4. Replacing the Chassis Air Filter
- 5. Required Tools and Equipment
- 6. Removing a Fan Tray
- 7. Installing a Fan Tray
- 8. Disconnecting AC Power
- 9. Reconnecting AC Power
- 10. Disconnecting DC Power
- 11. Reconnecting DC Power
Migrating from RSP4/RSP4-S/RSP-L to RSP5 Card
0/0/CPU0
0/2/CPU0
0/3/CPU0
Migrating from RSP4/RSP4-S/RSP-L to RSP5 Card
Before you begin:
• You must have console access to the router. Default console speed on RSP5 is set as 115200.
• The router must be running Cisco 64-bit IOS XR software release 6.5.15 or later version. If your router
• The router must have two RSP4/S/L cards (active and standby) up and running. In this section, RSP
• First and second generation Cisco ASR 9000 Ethernet Line Cards must be removed from the chassis as
Procedure
Step 1
Use the show redundancy summary command to verify that the RSP0 and RSP1 are in Ready State.
Example:
Router# show redundancy summary
Active/Primary Standby/Backup
-------------- --------------
0/RSP0/CPU0(A)
0/RSP1/CPU0(P)
Step 2
Shutdown the standby RSP card (slot 1) using the admin hw-module shutdown location 0/RSP1 command.
Step 3
Remove the standby RSP card (slot 1). When RSP is removed, an alarm is generated indicating that the
redundancy is lost. Follow the procedure explained in the topic
Chassis, on page
Step 4
Insert RSP5 in slot 1 and allow RSP5 to bootup.
Step 5
Verify both the RSPs are in IOS XR RUN state using the show platform command.
Example:
Router#show platform
Node
--------------------------------------------------------------------------------
Replacing Cisco ASR 9000 Series Router Components
38
A99-8X100GE-TR
A99-12X100GE
A99-8X100GE-TR
is running a 32-bit IOS XR release, you will need to migrate to 64-bit XR release 6.5.15 or later. Refer
to
Migration Guide for Cisco ASR 9000 Series
Note
RSP5 is only supported with 64-bit IOS XR software releases.
refers to RSP4/RSP4-S/RSP4-L in the system.
they are incompatible with RSP5.
0/RSP1/CPU0(S) (Node Ready, NSR: Ready)
0/RSP1/CPU0(B) (Proc Group Ready, NSR: Ready)
25.
Type
Replacing Cisco ASR 9000 Series Router Components
IOS XR RUN
PWR,NSHUT,MON
IOS XR RUN
PWR,NSHUT,MON
IOS XR RUN
PWR,NSHUT,MON
Routers.
Removing and Replacing Cards from the
State
Config state