Cisco 7513 Series 교체 지침 매뉴얼 - 페이지 15

{카테고리_이름} Cisco 7513 Series에 대한 교체 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 7513 Series 22 페이지. Chassis replacement
Cisco 7513 Series에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (44 페이지), 교체 지침 매뉴얼 (26 페이지), 데이터시트 (11 페이지), 매뉴얼 (30 페이지), 유지 관리 (20 페이지), 교체 지침 매뉴얼 (19 페이지)

페이지 인쇄

Follow these steps to move the processor modules to the new chassis:

Before moving any processor modules, ensure that you have met the following

Step 1

prerequisites (refer to the section "Prerequisites" on page 3 for details):

•

On both chassis, ensure that the power is turned OFF and the power cable is

disconnected from the AC power receptacle or the DC terminal block.

•

To prevent ESD damage, wear a grounding strap or other ESD-prevention device and

attach the equipment end to the chassis ground screw on the interface processor end of

the chassis. (See Figure 1.)

•

If you will leave the interface cables connected to the processor modules, ensure that

there is sufﬁcient slack to avoid straining the cables when moving the processor module

between chassis. Otherwise, label each cable with its slot and port number position.

(This will help avoid mixing up cables when you reconnect them.)

•

Optional: Install the cable-management brackets on the new chassis before moving the

components. Either move the brackets from the old chassis or install a new set.

Note the slot location of the interface processor you are going to move. Before removing

Step 2

the interface processor, remove the interface processor ﬁller from the corresponding slot in

the new chassis. When installing interface processors in the new chassis, place them in the

same slot position that they occupied in the old chassis; this will retain your existing

conﬁguration and will help avoid confusion when reconnecting cables and checking the

installation.

Step 3

If necessary, disconnect any interface cables that are connected to the processor module.

Use a screwdriver to loosen both of the captive installation screws on the processor module.

Step 4

(See Figure 7a.)

Step 5

Place your thumbs on the end of each ejector and simultaneously pull both ejectors

outward, away from the carrier handle (in the opposite direction from that show in

Figure 7c) to release the processor module from the backplane.

You must install the RSP2 in one of the slots labeled RSP (slot 6 or 7). We recommend

Caution

that you place the RSP2 in the same slot in the new chassis that it occupied in the old one. You can

install interface processors in any of the interface processor slots (the lowest slots), but we

recommend that you install them in the same slot positions that they occupied in the old chassis. The

slots are keyed for correct installation. Forcing a processor module into the wrong slot can damage

the backplane and board connectors.

Step 6

Grasp the processor module handle with one hand and pull the processor module straight

out of the slot, keeping your other hand under the carrier to guide it. (See Figure 8.) Keep

the carrier at a 90-degree orientation to the backplane. Avoid touching the board or any

connector pins.

Step 7

Place the processor module in the same slot position in the new chassis and align the

notches along the edge of the carrier with the grooves in the slot. (See Figure 7a.)

Step 8

While keeping the carrier at a 90-degree orientation to the backplane, carefully slide the

carrier into the slot until the back of the faceplate makes contact with the ejector levers, then

stop. (See Figure 7b.)

Do not use unnecessary force when installing processor modules. Always guide the carrier

into the slot only until the carrier faceplate makes contact with the ejector levers; then use

the ejector levers to complete the insertion.

Cisco 7513 Chassis Replacement Instructions

Replacing the Chassis