Cisco 7513 Series Değiştirme Talimatları Kılavuzu - Sayfa 15
Sunucu Cisco 7513 Series için çevrimiçi göz atın veya pdf Değiştirme Talimatları Kılavuzu indirin. Cisco 7513 Series 22 sayfaları. Chassis replacement
Ayrıca Cisco 7513 Series için: Hızlı Başlangıç Kılavuzu (44 sayfalar), Değiştirme Talimatları Kılavuzu (26 sayfalar), Veri Sayfası (11 sayfalar), Manuel (30 sayfalar), Bakım (20 sayfalar), Değiştirme Talimatları Kılavuzu (19 sayfalar)
Sayfayı Yazdır
Follow these steps to move the processor modules to the new chassis:
Before moving any processor modules, ensure that you have met the following
Step 1
prerequisites (refer to the section "Prerequisites" on page 3 for details):
•
On both chassis, ensure that the power is turned OFF and the power cable is
disconnected from the AC power receptacle or the DC terminal block.
•
To prevent ESD damage, wear a grounding strap or other ESD-prevention device and
attach the equipment end to the chassis ground screw on the interface processor end of
the chassis. (See Figure 1.)
•
If you will leave the interface cables connected to the processor modules, ensure that
there is sufficient slack to avoid straining the cables when moving the processor module
between chassis. Otherwise, label each cable with its slot and port number position.
(This will help avoid mixing up cables when you reconnect them.)
•
Optional: Install the cable-management brackets on the new chassis before moving the
components. Either move the brackets from the old chassis or install a new set.
Note the slot location of the interface processor you are going to move. Before removing
Step 2
the interface processor, remove the interface processor filler from the corresponding slot in
the new chassis. When installing interface processors in the new chassis, place them in the
same slot position that they occupied in the old chassis; this will retain your existing
configuration and will help avoid confusion when reconnecting cables and checking the
installation.
Step 3
If necessary, disconnect any interface cables that are connected to the processor module.
Use a screwdriver to loosen both of the captive installation screws on the processor module.
Step 4
(See Figure 7a.)
Step 5
Place your thumbs on the end of each ejector and simultaneously pull both ejectors
outward, away from the carrier handle (in the opposite direction from that show in
Figure 7c) to release the processor module from the backplane.
You must install the RSP2 in one of the slots labeled RSP (slot 6 or 7). We recommend
Caution
that you place the RSP2 in the same slot in the new chassis that it occupied in the old one. You can
install interface processors in any of the interface processor slots (the lowest slots), but we
recommend that you install them in the same slot positions that they occupied in the old chassis. The
slots are keyed for correct installation. Forcing a processor module into the wrong slot can damage
the backplane and board connectors.
Step 6
Grasp the processor module handle with one hand and pull the processor module straight
out of the slot, keeping your other hand under the carrier to guide it. (See Figure 8.) Keep
the carrier at a 90-degree orientation to the backplane. Avoid touching the board or any
connector pins.
Step 7
Place the processor module in the same slot position in the new chassis and align the
notches along the edge of the carrier with the grooves in the slot. (See Figure 7a.)
Step 8
While keeping the carrier at a 90-degree orientation to the backplane, carefully slide the
carrier into the slot until the back of the faceplate makes contact with the ejector levers, then
stop. (See Figure 7b.)
Do not use unnecessary force when installing processor modules. Always guide the carrier
into the slot only until the carrier faceplate makes contact with the ejector levers; then use
the ejector levers to complete the insertion.
Cisco 7513 Chassis Replacement Instructions
Replacing the Chassis
15