Cisco TelePresence 관리자 매뉴얼 - 페이지 17
{카테고리_이름} Cisco TelePresence에 대한 관리자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco TelePresence 27 페이지. Configuring a cisco unified communications
manager sip trunk with a cisco telepresence content server
Cisco TelePresence에 대해서도 마찬가지입니다: 브로셔 (4 페이지), 사양 (7 페이지), 설치 매뉴얼 (4 페이지), 빠른 참조 매뉴얼 (2 페이지), 매뉴얼 (24 페이지), 설치 시트 (2 페이지)
Cisco TelePresence ISDN Link
Contents
Introduction
Example with ISDN BRI Euro type
In this example the ISDN type is BRI and European type, the number is 8001-8004, and the
endpoint is connected directly to the ISDN Link. There is no IP infrastructure and the endpoint must
not be registered to VCS when using this configuration.
Endpoint configuration
Use the Remote Control or Touch panel to configure.
Network 1 > Assignment = Manual
Network 1 > IPv4 > Address = 192.168.1.100
Network 1 > IPv4 > SubnetMask = 255.255.255.0
Network 1 > IPv4 > Gateway = 192.168.1.1
Conference 1 > DefaultCall > Protocol = SIP
Conference 1 > DefaultCall > Rate: 512 (Euro BRI 4 channels @ 128 kbps)
ISDN Link configuration
Use the serial port to configure.
xConfiguration Network 1 Assignment: Static
(Set Static IP)
xConfiguration Network 1 IPv4 Address: "192.168.1.101"
(Set the IP address of the ISDN Link)
xConfiguration Network 1 IPv4 SubnetMask: "255.255.255.0"
(Set the subnet mask of the ISDN Link)
xConfiguration Gateway SIP PeerHost: "192.168.1.100"
(Set the IP address of the endpoint)
xConfiguration H320 NetType: BRI
(Set type of ISDN)
xConfiguration ISDN BRI SwitchType: Euro
(Set the ISDN switch type; must match switch type in Adtran)
xConfiguration ISDN BRI Interface 1 Mode: On
xConfiguration ISDN BRI Interface 2 Mode: On
xConfiguration ISDN BRI Interface 3 Mode: On
xConfiguration ISDN BRI Interface 4 Mode: On
(Enable the BRI interfaces)
xConfiguration ISDN BRI Interface 1 DirectoryNumber 1 Number: "8001"
xConfiguration ISDN BRI Interface 2 DirectoryNumber 1 Number: "8002"
xConfiguration ISDN BRI Interface 3 DirectoryNumber 1 Number: "8003"
xConfiguration ISDN BRI Interface 4 DirectoryNumber 1 Number: "8004"
(Enter your BRI numbers, this MUST be according to the ISDN network configuration.)
D14954.01
ISDN Link Administrator Guide IL1.0, June 2012.
Copyright © 2012 Cisco Systems, Inc. All rights reserved.
Getting started
Configuration examples
Configuration examples
ISDN only
Dialling from the endpoint
From the endpoint you should now be able to dial an ISDN number using the following format:
Format: <ip address>;x-h320number=XXXX
• Where XXXX is the ISDN number you wish to call.
• In this case, with no IP infrastructure, we use the IP Address to identify the ISDN Link.
Example: 192.168.1.101;x-h320number=1234
17
Password protection
Appendices
EX90
ISDN Network
ISDN Link
Administrator guide
Contact us
www.cisco.com