Cisco TelePresence 관리자 매뉴얼 - 페이지 19
{카테고리_이름} Cisco TelePresence에 대한 관리자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco TelePresence 27 페이지. Configuring a cisco unified communications
manager sip trunk with a cisco telepresence content server
Cisco TelePresence에 대해서도 마찬가지입니다: 브로셔 (4 페이지), 사양 (7 페이지), 설치 매뉴얼 (4 페이지), 빠른 참조 매뉴얼 (2 페이지), 매뉴얼 (24 페이지), 설치 시트 (2 페이지)
페이지 인쇄
Cisco TelePresence ISDN Link
Contents
Introduction
Example with full IP infrastructure and VCS
In this example the ISDN type is Euro BRI with four BRI lines (4 x 128 kbps), the number range is
8001-8004, and the endpoint is set-up and registered to a VCS*.
Endpoint configuration
Use the Remote Control or Touch panel to configure.
Network 1 > Assignment = DHCP
SIP Profile 1 > URI 1 = [email protected]
SIP Profile 1 > Proxy 1 > Address: "sip.registrar.domain.com"
Conference 1 > DefaultCall > Protocol = SIP
Conference 1 > DefaultCall > Rate: 512 (Euro BRI 4 lines @ 128 kbps)
ISDN Link configuration
Use the serial port or SSH to configure.
xConfiguration H320 NetType: BRI
(Set network type)
xConfiguration Network 1 Assignment: DHCP
(Set network assignment)
xConfiguration Gateway SIP PeerHost: "192.168.1.100"
(Set the IP address of the endpoint)
xConfiguration ISDN BRI SwitchType: Euro
(Set the ISDN switch type)
xConfiguration ISDN BRI Interface 1 Mode: On
xConfiguration ISDN BRI Interface 2 Mode: On
xConfiguration ISDN BRI Interface 3 Mode: On
xConfiguration ISDN BRI Interface 4 Mode: On
(Enable the BRI interfaces)
xConfiguration ISDN BRI Interface 1 DirectoryNumber 1 Number: "8001"
xConfiguration ISDN BRI Interface 2 DirectoryNumber 1 Number: "8002"
xConfiguration ISDN BRI Interface 3 DirectoryNumber 1 Number: "8003"
xConfiguration ISDN BRI Interface 4 DirectoryNumber 1 Number: "8004"
(Enter your BRI numbers, this MUST be according to the ISDN network configuration.)
xConfiguration Gateway SIP PeerUri: "[email protected]"
(Set URI for the endpoint)
xConfiguration SIP Profile 1 URI: "[email protected]"
(Set URI for ISDN Link. The ISDN Link must be SIP registered)
D14954.01
ISDN Link Administrator Guide IL1.0, June 2012.
Copyright © 2012 Cisco Systems, Inc. All rights reserved.
Getting started
Configuration examples
Configuration examples
Confirm that the ISDN Link is SIP registered
• xStatus SIP
Dialling from the endpoint
From the endpoint you should now be able to dial an ISDN number using the following format:
Format: <sip uri>;x-h320number=XXXX
• Where XXXX is the ISDN number you wish to call.
• In this case, with an IP infrastructure in place, we use the SIP URI to identify the ISDN Link.
Example: [email protected];x-h320number=1234
19
Password protection
Combining ISDN and IP
ISDN Network
ISDN Link
xConfiguration SIP Profile 1 Proxy 1 Address: "sip.registrar.domain.com"
(Set address of SIP registrar)
Administrator guide
Appendices
Contact us
C40
IP Network
* VCS = Cisco TelePresence Video Communication Server
www.cisco.com