Epson Stylus Color 660 제품 정보 - 페이지 8

{카테고리_이름} Epson Stylus Color 660에 대한 제품 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson Stylus Color 660 11 페이지. Color ink jet printer
Epson Stylus Color 660에 대해서도 마찬가지입니다: 사용자 설명서 (34 페이지), 제품 정보 시트 (4 페이지), 사양 시트 (2 페이지), 제품 정보 시트 (4 페이지), 여기에서 시작하기 매뉴얼 (20 페이지), 서비스 매뉴얼 (40 페이지)

Epson Stylus Color 660 제품 정보
EPSON Stylus COLOR 660

Replacing an Outdated Ink Cartridge

If an ink cartridge is more than six months old, you may need
to replace it. How can you tell? You may notice that your
printouts don't look as good as they used to. If print quality
doesn't improve after cleaning and aligning the print head, try
replacing one or both cartridges.
Follow these steps to replace an ink cartridge before the
B black or A color ink out light is flashing or on:
1. Make sure the printer is turned on and not printing (the
P power light should be on, but not flashing).
2. Lower the output tray and raise the printer cover.
3. Press the E load/eject button and hold it down for a few
seconds until the print head moves to the left and the
P power light begins flashing.
Never move the print head by hand.
Don't open the clamp or remove a cartridge except to
replace it with a new one. Once you remove a cartridge,
you can't reuse it.
4. Unwrap the new ink cartridge. Then pull off only the
yellow part of the tape seal on the top of the cartridge.
You must remove only the yellow tape seal from the top
of the cartridge; leaving the tape on will permanently
damage it. Do not remove the clear seal from the bottom
of the cartridge; ink will leak.
black cartridge
5. Pull up the ink cartridge clamp. The cartridge rises up from
its holder. (The illustration shows the color ink cartridge
replacement. To replace the black ink cartridge, lift up only
the smaller clamp on the left.)
8 - EPSON Stylus COLOR 660
color cartridge
6. Lift the cartridge out of the printer and dispose of it
carefully.
Keep ink cartridges out of the reach of children.
If ink gets on your hands, wash them thoroughly with
soap and water. If ink gets in your eyes, flush them
immediately with water.
7. Lower the new ink cartridge into its holder with the label
facing up and toward the back of the printer.
8. Press down the ink cartridge clamp until it locks in place.
9. Press the E load/eject button and close the printer cover.
The printer moves the print head and begins charging the ink
delivery system. The P power light flashes and the printer
makes various sounds. Charging takes about one minute.
When it's finished, you can print again.
Never turn off the printer while the P power light is
flashing, unless the printer hasn't moved or made any
noise for more than 5 minutes.

Cleaning the Print Head

If your printed image is unexpectedly light or faint, or dots are
missing from the image, you may need to clean the print head.
This unclogs the nozzles so they can deliver ink properly.
Don't use the cleaning sheets that may be included with
your special media; they may damage the printer.
Cleaning the print head uses ink, so clean it only if print
quality declines. You can use either of the following to clean
the print head:
The Head Cleaning utility in your printer software (if the
printer is on a local port rather than a network)
The printer's control panel buttons.
Note:
When you don't turn on your printer for a long time, the print quality
can decline. It's a good idea to turn on your printer at least once a
month to maintain good print quality.
8/99