Motorola CP160 서비스 정보 - 페이지 11

{카테고리_이름} Motorola CP160에 대한 서비스 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Motorola CP160 46 페이지. Uhf2 (438-470mhz)
Motorola CP160에 대해서도 마찬가지입니다: 사용자 설명서 (46 페이지), 기본 사용 설명서 (16 페이지), 기본 사용 설명서 (16 페이지), 기본 사용 설명서 (18 페이지), 자세한 서비스 매뉴얼 (28 페이지), Cps/튜너 설치 매뉴얼 (6 페이지), 서비스 정보 (46 페이지)

UHF (465-495MHz) Receiver

2.2

Receiver Back End

The receiver back end is a dual conversion design. High IF selectivity is provided by FL51, a 4-pole

fundamental mode 44.85 MHz crystal filter with a minimum 3 dB bandwidth of ±6.7 kHz, a maximum

20 dB bandwidth of + 12.5 kHz, and a maximum insertion loss of 3.5 dB. The output is matched to IF

amplifier stage Q51 by L53 and C93. Q51 provides 16 dB of gain and a noise figure of 1.8 dB. The

dc operating current is 1 mA. The output of Q51 is applied to the input of the receiver IFIC U51.

Diode CR51 limits the maximum RF level applied to the IFIC.

The IFIC is a low-voltage monolithic FM IF system incorporating a mixer/oscillator, two limiting IF

amplifiers, quadrature detector, logarithmic received signal strength indicator (RSSI), voltage

regulator and audio and RSSI op amps. The second LO frequency, 44.395 MHz, is determined by

Y51. The second mixer converts the 44.85 MHz high IF frequency to 455 kHz.

Additional IF selectivity is provided by two ceramic filters, FL52 (between the second mixer and IF

amp) and FL53 or FL54 (between the IF amp and the limiter input). The wider filter FL53 is used for

20/25 kHz channel spacing, and the narrower filter FL54 is used for 12.5 kHz channels. When the

BW_SEL line is high, the two upper diodes in packages D51 and D52 are forward biased, selecting

FL53 for 20/25 kHz channels. When the BW_SEL line is low, the two lower diodes in packages D51

and D52 are forward biased, selecting FL54 for 12.5 kHz channels.

The ceramic filters have the following specifications:

Ceramic resonator Y70 provides phase vs. frequency characteristic required by the quadrature

detector, with 90 degree phase shift occurring at 455 kHz. Buffer Q70 provides a lower driving

impedance from the limiter to the resonator, improving the IF waveform and lowering the distortion

of the recovered audio signal. The recovered audio level at the DEMOD output is 100 mV rms (25

kHz channel, 3 kHz deviation) or 50 mV rms (12.5 kHz channel, 1.5 kHz deviation). An additional

RSSI output provides a DC voltage level that is proportional to RF signal level. This voltage is

measured by an A/D converter contained in the microprocessor (PE4_AN4, U401 pin 63).

Number of Elements:

Insertion Loss:

6 dB Bandwidth:

50 dB Bandwidth:

Stopband Rejection:

FL52

FL53

4 dB

15 kHz

30 kHz

27 dB

47 dB

FL54

4 dB

9 kHz

22 kHz

47 dB

2-3