Epson 1815p - PowerLite XGA LCD Projector 사용자 설명서 - 페이지 25

{카테고리_이름} Epson 1815p - PowerLite XGA LCD Projector에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 1815p - PowerLite XGA LCD Projector 27 페이지. Release of check tool for network projectors v1.00 for windows
Epson 1815p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 운영 매뉴얼 (47 페이지), 빠른 설정 (2 페이지), 사용자 설명서 (1 페이지), 기능 설명서 (5 페이지), 소프트웨어 설명서 (2 페이지), 적합성 선언 (4 페이지), 부품 목록 (1 페이지), 제품 지원 게시판 (45 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄
Epson 1815p - PowerLite XGA LCD Projector 사용자 설명서

Replacing the Lamp and Air Filter

The life span of the projection lamp is about 2,500 hours if
in the Settings menu is set to
Brightness Control
(default), and 3,000 hours if
It is time to replace the lamp when:
❏ The projected image gets darker or starts to deteriorate.
❏ The message
Replace the lamp
the lamp comes on and the lamp warning light
orange. To maintain projector brightness and image quality,
replace the lamp as soon as possible.
❏ The lamp warning light
out).
Lamp
warning
light
Follow these steps to replace the lamp and air filter:
1. Turn off the projector and unplug the power cord.
2. Let the projector cool for at least an hour (if it has been on).
The lamp is extremely hot immediately after use.
3. Loosen the lamp cover screw (you don't need to remove it).
Then slide the lamp cover to the side and lift it off the
projector.
High
is set to
Brightness Control
appears on the screen when
flashes
flashes red (the lamp is burnt
4. Loosen the two screws holding the lamp in place (you can't
remove them).
.
Low
5. Hold the lamp as shown and pull it straight out.
6. Gently insert the new lamp. (If it doesn't fit easily, make sure
it is facing the right way.)
7. Once the lamp is fully inserted, tighten its screws.
8. Replace the lamp cover, then tighten its screw.
9. Slide out the air filter on the bottom of the projector and
remove it.
10.Slide in the new air filter until it clicks in place.
11.Reset the lamp timer as described in the next section.
Note: When you get a replacement lamp for your projector, you
should replace the filter. Turn off this product when not in use to
prolong the life of the projector.
3/08
PowerLite 1810p/1815p
Loosen, but don't
remove these screws
PowerLite 1810p/1815p
25
-