Epson 6110i - PowerLite XGA LCD Projector 사용자 설명서 - 페이지 9

{카테고리_이름} Epson 6110i - PowerLite XGA LCD Projector에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 6110i - PowerLite XGA LCD Projector 17 페이지. Release of emp ns connection for windows & mac upgrade from v2.50 to v2.51
Epson 6110i - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 운영 매뉴얼 (47 페이지), 사양 (2 페이지), 보충 설명서 (1 페이지), 빠른 설정 매뉴얼 (7 페이지), 사용자 설명서 (1 페이지), 부품 목록 (1 페이지), 적합성 선언 (4 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄
Epson 6110i - PowerLite XGA LCD Projector 사용자 설명서
Operating Two or More Projectors
with the Remote Control
If you're using more than one projector, you can control all
the projectors—or just selected ones—by using the projector
ID system. To operate a projector, you have to set the remote
control's ID to match that of the projector. Or you can
control all the projectors at once by setting the remote
control's ID to zero.
Setting the Projector ID
The projector's default ID is set to Off. This lets it respond to
commands from any remote control. To change the ID,
follow these steps:
1. Press the
button on the remote control.
Menu
2. Select
Extended > Projector ID
3. Use the
pointer button to highlight the new ID, and
press
to select it.
Enter
4. When done, press
Menu
Setting the Remote Control ID
The remote control's default ID is zero. This lets you operate
any projector. To set it to operate a specific projector, follow
these steps:
1. Point the remote control at the projector you want to be
able to operate.
Note: If you're using a remote control ID other than the default
ID of zero, you have to set the ID each time you turn on the
projector.
.
to exit the menu system.
2. Press and hold the
3. While holding the ID button, press a numbered button on
the remote control (0 through 9) to select the desired ID.
Select zero to control all projectors, or select a number to
match the ID of the projector(s) you want to operate.
After setting the ID, you can check whether the remote
control works with a specific projector:
1. Point the remote control at the projector you want to check.
2. Press the
button on the remote control. You see a
ID
message on the screen like one of these:
If the message says the remote control is
use the remote control to operate that projector. If it says
, then you have to change the ID of the remote control
Off
and/or projector before operation is possible.

Projector Status Lights

The lights on top of the projector indicate the projector's
status and let you know when a problem occurs.
Power light
Refer to the following table for a complete description of the
projector's status lights and their meanings.
12/07
Epson PowerLite 6110i
button on the remote control.
ID
, then you can
On
Lamp light
Temperature light
Filter light
9