Epson 7850p - PowerLite XGA LCD Projector 제품 정보 매뉴얼 - 페이지 8

{카테고리_이름} Epson 7850p - PowerLite XGA LCD Projector에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 7850p - PowerLite XGA LCD Projector 25 페이지. Release of check tool for network projectors v1.00 for windows
Epson 7850p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 사용자 설명서 (12 페이지), 교체 부품 (1 페이지), 운영 매뉴얼 (47 페이지), 제품 지원 게시판 (30 페이지), 설치 매뉴얼 (5 페이지), 빠른 설정 (2 페이지), 브로셔 및 사양 (2 페이지), 기술 요약 (7 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄

Epson 7850p - PowerLite XGA LCD Projector 제품 정보 매뉴얼

Adjusting the Image

Once you see your image, you may need to make certain

adjustments.

Focusing and Zooming Your Image

Use the focus ring on the projector to sharpen the image.

Use the zoom ring on the projector to reduce or enlarge the

image. Move the tab toward the

toward the

to make it smaller.

Focus ring

If the image still isn't large enough, you may need to move the

projector farther away from the screen. You can also use the

buttons on the remote control to zoom in on a

E-Zoom

portion of the image.

Adjusting the Height of Your Image

If the image is too low on the screen, you can raise it by

adjusting the front foot:

1. Stand behind the projector. Press the blue foot release lever

up and lift the front of the projector.

2. Once the image is positioned where you want it, release the

lever to lock the foot in position.

3. If necessary, you can fine-

tune the height by turning

the projector's rear feet.

to make it bigger, or

Zoom ring

Projector foot

EPSON PowerLite 7850p Projector

Raising the projector causes the image to distort or

"keystone," but you can manually correct the shape as

described in the next section.

Adjusting the Image Shape

In most cases, you can maintain a rectangular image by

placing the projector directly in front of the center of the

screen with the base of the lens level with the bottom of the

screen.

Even if the projector is slightly tilted (within a range of 40° up

or down), the projector's automatic keystone correction

function detects and corrects vertical keystone distortion.

Projector tilted up

It takes about one second after projection starts for the image

to be corrected. During this time, a vertical keystone

correction gauge appears on the screen.

If your image is still distorted, you can correct it using either

of these methods:

❏ If the image has two parallel

sides but is wider on the top,

bottom, left, or right, you

can correct it using the

keys on the

Keystone

projector's control panel or

the Keystone menu (see

"Using Keystone

Correction" on page 7).

❏ If the image has no parallel

sides, you can adjust its

shape using Quick Corner

(see page 8).

You cannot use both keystone

correction and Quick Corner at the same time.

Using Keystone Correction

To adjust your image when it is wider on one side, do one of

the following:

❏ Look at the shapes of the icons on the

projector's four

Keystone

Press the button whose icon is the

opposite shape of your screen image.

Continue pressing the button until

you are satisfied with the shape of the

image.

6/03

EPSON PowerLite 7850p Projector

Corrected image

Projector tilted down

Keystone correction

™

Quick Corner correction

buttons.