Epson 7850p - PowerLite XGA LCD Projector 제품 정보 매뉴얼 - 페이지 6

{카테고리_이름} Epson 7850p - PowerLite XGA LCD Projector에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 7850p - PowerLite XGA LCD Projector 25 페이지. Release of check tool for network projectors v1.00 for windows
Epson 7850p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 사용자 설명서 (12 페이지), 교체 부품 (1 페이지), 운영 매뉴얼 (47 페이지), 제품 지원 게시판 (30 페이지), 설치 매뉴얼 (5 페이지), 빠른 설정 (2 페이지), 브로셔 및 사양 (2 페이지), 기술 요약 (7 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄
Epson 7850p - PowerLite XGA LCD Projector 제품 정보 매뉴얼

Starting Up the Projector

If you turn on your computer or video equipment before the
projector, the projector automatically selects the connected
source. If you turn on the projector first or you have multiple
sources connected, you may have to switch to the desired
source manually (see "Selecting the Image Source" on page 5).
Turning On the Projector
1. Remove the lens cap.
2. Plug in the projector.
3. Wait a few seconds until the projector's P power light stops
flashing and turns orange.
4. Press the red P
Power
the remote control.
Note: If you're using the remote
control, make sure batteries are
installed and the power switch on
the side of the remote control is
turned on.
The projector's P power light flashes green as it warms up,
and an image begins to appear after about 30 seconds.
When the P power light stops flashing and remains green,
the projector is ready for use.
Warning: Never look into the lens when the lamp is on. This
can damage your eyes.
5. If you've connected a Windows-based computer to the
projector, you may see a New Hardware Wizard saying
your computer has found a plug-and-play monitor; if so,
click
.
Cancel
Selecting the Image Source
If multiple devices are connected to the projector, you can use
the
buttons on the projector or the remote control to
Source
switch from one source to another:
button on top of the projector or on
Power button
EPSON PowerLite 7850p Projector
❏ The projector's control panel has two
Use the
Computer/DVI
switch between EasyMP,
between equipment connected to the
and
Computer
DVI
Use the
Video/BNC
between equipment connected to the
,
, and
Video
S-Video
❏ The remote control has six
buttons. Use them to switch
between equipment connected to
the port identified on each button,
or select
EasyMP
wirelessly or from a memory card.
You can preview all sources to help
you select the desired source, as described below.
The
and
Computer
input signals, so if you have equipment connected to one of
these ports, be sure to select the correct signal to match the
equipment you're using. You can change the input signal
settings using the projector's menu system as described in
"Types of Connections" on page 4.
Previewing Image Sources
Use the preview function to select the image source when you
have connected multiple sources to the projector.
1. Press the
Preview
remote control.
You see the currently selected
source displayed on the screen, as
shown below. Other sources
(including the currently selected source) appear in smaller
preview windows on the right and bottom of the screen.
.
Currently selected source
BNC
If no equipment is connected to a port, or if there is no
incoming signal, the preview window for that source
appears blank.
Note: Movies are displayed as still images on the preview
screen.
6/03
EPSON PowerLite 7850p Projector
Source
button to
™
and
ports.
button to switch
ports.
BNC
Source
to project
ports can be set up to use different
BNC
button on the
Preview
Computer (Analog-RGB)
Computer
DVI
Video
S-Video
Preview windows
buttons.
5
-