Epson 890N - FX B/W Dot-matrix Printer 제품 정보 매뉴얼 - 페이지 5
{카테고리_이름} Epson 890N - FX B/W Dot-matrix Printer에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 890N - FX B/W Dot-matrix Printer 19 페이지. Impact printers
Epson 890N - FX B/W Dot-matrix Printer에 대해서도 마찬가지입니다: 사용자 설명서 (48 페이지), 매뉴얼 (11 페이지), 사양 (2 페이지), 기술 요약 (7 페이지)
페이지 인쇄
EPSON FX-890/FX-2190
Environmental
Temperature
Operation (plain
41 to 95 °F (5 to 35 °C)
paper)
Operation
59 to 77 °F (15 to 25 °C)
(recycled paper,
envelopes, labels
or roll paper)
Storage
–22 to 140 °F (–30 to 60 °C)
Paper
Use recycled paper, multipart paper, labels, envelopes, and roll
paper only under normal temperature and humidity conditions,
as follows:
Temperature
Humidity
Do not load paper that has been folded or is damaged,
wrinkled, or curled.
Single sheets, front or rear entry
Minimum
Width
*
(inch)
3.9
(mm)
100
**
Length
(inch)
3.9
(mm)
100
***
Thickness
(inch)
0.0025
(mm)
0.065
Weight
(lb)
14
(g/m²)
52
Quality
Plain paper and recycled paper
* 7.2 to 8.5 inches (182 to 216 mm) using the optional cut-sheet
feeder for FX-890.
7.2 to 16.5 inches (182 to 420 mm) using the optional cut-sheet
feeder for FX-2190.
** 8.3 to 14.3 inches (210 to 364 mm) using the optional cut-sheet
feeder.
***0.0028 to 0.0055 inch (0.07 to 0.14 mm) using the optional
cut-sheet feeder.
4 - EPSON FX-890/FX-2190
Humidity (without
condensation)
10 to 80% RH
30 to 60% RH
0 to 85% RH
59 to 77 °F (15 to 25 °C)
30 to 60% RH
Maximum
FX-890:
FX-2190:
10.1
16.5
257
420
14.3
364
0.0055
0.14
24
90
Single-sheet multipart forms (for the optional front
sheet or front paper guide only):
Width
(inch)
(mm)
Length
((inch)
(mm)
Copies
Total thickness
(inch)
(mm)
Weight per sheet of
multipart
(lb)
(g/m²)
Quality
Continuous paper (ordinary and multipart):
Width
(inch)
(mm)
Length, one page
(inch)
(mm)
Copies
Total thickness
(inch)
(mm)
Weight, ordinary
paper
(lb)
(g/m²)
Weight per sheet of
multipart
(lb)
(g/m²)
Quality
Do not load thick paper, such as multipart forms with five or six
parts, in the rear slot.
The ratio of the cut/uncut length at the perforation should be
between 3:1 and 5:1.
The thickness of the perforation part when extended should be
1 mm or less.
The perforation between pages should not extend all the way to
the edges of the paper. Uncut length on the edges should be
1 mm or more.
The horizontal and vertical perforation cuts should not cross.
6/03
Minimum
Maximum
FX-890:
3.9
10.1
100
257
3.9
14.3
100
364
1 original + 5 copies
0.0047
0.018
0.12
0.46
12
15
40
58
Carbonless multipart forms with a line of glue at
the top or one side of the form
Minimum
Maximum
FX-890:
4.0
10.0
101.6
254.0
4.0
22.0
101.6
558.8
1 original + 5 copies
0.0025
0.018
0.065
0.46
14
22
52
82
12
15
40
58
Plain paper, recycled paper, and carbonless
multipart forms with point gluing or paper
stapling on both sides
FX-2190:
16.5
420
16.5
420
FX-2190:
16.0
406.4