Epson PowerLite 737c 제품 정보 - 페이지 18

{카테고리_이름} Epson PowerLite 737c에 대한 제품 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson PowerLite 737c 24 페이지. Release of check tool for network projectors v1.00 for windows
Epson PowerLite 737c에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 빠른 설정 매뉴얼 (2 페이지), 운영 매뉴얼 (47 페이지), 부품 목록 (1 페이지), 제품 지원 게시판 (30 페이지), 설치 매뉴얼 (19 페이지), 사용자 설명서 (1 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지), 빠른 설정 (2 페이지)

페이지 인쇄
Epson PowerLite 737c 제품 정보
Epson PowerLite 737c Projector
Managing Projectors from a Remote
Computer
The software included with your projector lets you monitor
and control projector(s) from a remote computer. These
features are intended for use by network administrators.
❏ Use EMP Monitor to see your projectors' status, switch
image sources, and control basic settings.
❏ Use the mail notification function to receive e-mail alerts
about possible problems.
❏ Use a network management utility running SNMP, such as
™
HP OpenView,
to manage your facility's equipment from
a pre-existing system.
Make sure you have installed the EMP Monitor software
(included on the projector's CD-ROM) on the computer you
want to use to monitor your projectors. (See the User's Guide
for instructions.)
Note:
Your computer must be running Microsoft Windows XP, 2000,
Me or 98SE.
Opening and Closing EMP Monitor
To start EMP Monitor, click
Programs > EPSON Projector > EMP Monitor
If you've added the program to the Startup programs folder, it
may already be open. If so, click the icon in the system tray on
the lower-right corner of your screen to display the EMP
Monitor window:
To close EMP Monitor, right-click the program icon shown
above, then select
.
Exit
18
Epson PowerLite 737c Projector
-
or
Start > Programs
All
.
Click here to start EMP Monitor
Registering Projectors in EMP Monitor
Before you can monitor a projector, you have to register it.
Follow these steps:
1. Open EMP Monitor. You see this screen:
Click here
2. Click
Register projector
3. Click
detect to locate projectors currently operating
Auto
on the network. Or click
projector's name and network address.
Note:
If Auto detect fails to find the projector, your projector may
not be connected or configured correctly for the network.
Any projectors found on the network are listed:
4. Select each projector you want to add by clicking its name
and clicking
. When you're done, click
Add
2/05
. You see this screen:
Click here
and enter the
Manual registration
Click here
.
Close