Philips 3 DISC SHELF SYSTEM W-10W FWC1C37 사용자 설명서 - 페이지 15

{카테고리_이름} Philips 3 DISC SHELF SYSTEM W-10W FWC1C37에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Philips 3 DISC SHELF SYSTEM W-10W FWC1C37 28 페이지. Philips home stereo system user's manual

Philips 3 DISC SHELF SYSTEM W-10W FWC1C37 사용자 설명서
15
• If you press DISC CHANGE again
during playback, the CD will stop
playing.
™ The CD carousel tray will rotate
until the inner tray is rotated out
and is ready for changing.
3 Press OPEN•CLOSE to close the
CD carousel tray.

Selecting a desired track

Selecting a desired track when
playback is stopped
1 Press í or ë until the desired
track appears on the display.
2 PressÉ to start playback.
™ The selected track number and
elapsed playing time appear on
the display.
Selecting a desired track during
playback
• Press í or ë until the desired
track appears on the display.
™ The selected track number and
elapsed playing time appear on
the display.
• If you press í once it will skip to
the beginning of the current track
and play the track again.
Note:
– Pressing í during shuffling can only
skip to the beginning of the current
track.
pg 01-28/C1-C10/37-En
Searching for a particular
passage during playback
• Press and hold à or á until the
desired passage is located.
™ The volume will be reduced.
• Play returns to normal when à or
á is released.
Programming Tracks
Programming tracks of a loaded CD is
possible when playback is stopped. The
display will indicate the total tracks
stored in the program. Up to 40 tracks
can be stored in the memory in any
order. When 40 tracks are stored and
you attempt to store another track, the
display will show "PROGRAM FULL".
1 Load the desired discs in the disc
trays.
2 Press PROGRAM to start
programming.
™ The PROG flag starts flashing.
™ It will cancel any previously
selected repeat mode.
3 Press the CD (CD 1•2•3) or DISC
1/2/3 button to select the disc.
4 Pressí or ë to select the desired
track.
5 Press PROGRAM to store the
track.
• Repeat steps 3 to 5 to store other
discs and tracks.
15
CD
6 Press Ç once to end programming.
™ The total number of tracks
programmed and total playing
time appear on the display.
Notes:
– If the total playing time is more than
"99:59" or if one of the programmed
tracks has a number greater than 30,
then "--:--" appears on the display
instead of the total playing time.
– If the system is reading the discs,
programming is not possible,
"READING" will be displayed and
followed by "DISC X". "X" is the
current read disc number.
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Reviewing the program
Reviewing of the program is possible
only when playback is stopped.
• Pressí or ë repeatedly to review
the programmed tracks.
• Press Ç to exit review mode.
Playing the program
1 Press É to start program playback.
™ "PLAY PROGRAM" will be
displayed.
™ The track number and elapsed
playing time of the current track
will appear on the display.
16/11/1999, 1:56 PM
• If you press REPEAT during
program playback, the current track
or all programmed tracks will be
played repeatedly.
™ "TRACK" or "PROGRAM" will be
displayed.
™ The REP and PROG flags appear
on the display.
2 Press Ç to stop program playback.
Notes:
– If you press any of the CD DIRECT
PLAY buttons, the system will play the
selected disc or track and the stored
program will be ignored temporarily.
The PROG display also will disappear
temporarily from the display. It will
reappear when playback of the
selected disc ends.
– REPEAT DISC mode will be cancelled
when program playback begins.

Erasing the program

(when
playback is stopped)
• Press Ç.
™ "PROGRAM CLEARED" will be
displayed.
Note:
– The program will be erased when the
system is disconnected from the power
supply or when the CD carousel tray is
opened.
3139 116 19292 (ENG)