Philips AZ 2045 사용자 설명서 - 페이지 11
{카테고리_이름} Philips AZ 2045에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Philips AZ 2045 15 페이지. Cd soundmachine
Philips AZ 2045에 대해서도 마찬가지입니다: 사용자 설명서 (9 페이지), 사양 (2 페이지), 사용자 설명서 (12 페이지), 매뉴얼 (8 페이지), 서비스 매뉴얼 (34 페이지), 매뉴얼 (10 페이지), (스웨덴어) Snabbmanual (8 페이지)
DIGITAL TUNER
3 Press and hold ∞ or § until the frequency in the
display starts running.
™ The radio automatically tunes to a station of
sufficient reception. Display shows
during automatic tuning.
™ If a FM station is received in stereo,
shown.
4 Repeat steps 2-3 if necessary until you find the
desired station.
• To tune to a weak station, press ∞ or § briefly
and repeatedly until you have found optimal
reception.
To improve radio reception:
• For FM, extend, incline and turn the telescopic
antenna. Reduce its length if the signal is too
strong.
• For AM, the set uses a built-in antenna. Direct this
antenna by turning the whole set.
Programming radio stations
You can store up to a total of 30 radio stations in the
memory, manually or automatically (Autostore).
Manual programming
1 Tune to your desired station (see Tuning to radio
stations).
2 Press PROG to activate programming.
3 Press PRESET DOWN/ UP once or more to select
a preset number.
4 Press PROG to confirm.
5 Repeat steps 1-4 to store other stations.
Note: You can erase a preset station by storing
another frequency in its place.
Autostore
Autostore automatically starts programming radio
stations from preset 1. Available stations are
programmed in order of waveband reception strength:
FM, followed by AM. Any previous presets e.g.
manually programmed will be erased.
• Press PROG for 4 seconds or more to activate
autostore programming.
™ The display shows
followed by the radio station details when
stored. (See 5)
, program blinks,
AUTO
After all stations are stored, the first autostore preset
station will then automatically play.
To listen to a preset or autostore station
Press the PRESET (up or down) buttons once or more
until the desired preset station is displayed.
is
Changing tuning grid (some versions only)
In North and South America the frequency step
between adjacent channels in the AM and FM band
are 10 KHz and 100 KHz respectively. In the rest of the
world this step is 9 KHz and 50 KHz. Usually the
frequency step has been preset in the factory for your
area.
1 Check that the set is completely switched off.
2 To select 9KHz: Simultaneously, press MODE and
PRESET DOWN on the set.
3 Switch the set on to TUNER and then release the
controls.
• To select 10KHz: Repeat steps 1-3 but in step 2,
simultaneously, press MODE and PRESET UP on
the set.
™ When you tune to radio stations, the display
shows tuning in either steps of 9 kHz or 10 kHz.
™ All preset and autostore stations will be
affected and you may need to reprogram
stations.
CD PLAYER
Playing a CD
This CD player plays Audio Discs including
CD-Recordables and CD-Rewritables.
1 Press y to on, then SOURCE to select
™
2 Insert a CD with the printed side facing up and
close the CD door.
™ Display: total number of tracks and playing time.
™
non-finalized CD-R(W).
CD
if no CD is inserted.
is shown if you have inserted a
CD
.