Toshiba XDE600KU 소유자 매뉴얼 - 페이지 37

{카테고리_이름} Toshiba XDE600KU에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Toshiba XDE600KU 40 페이지. Upconverting 1080p extended detail dvd player
Toshiba XDE600KU에 대해서도 마찬가지입니다: 소유자 매뉴얼 (40 페이지)

페이지 인쇄

Others

Before Calling Service Personnel

Check the following guide for the possible cause of a problem before contacting service.

Symptoms and correction

Symptom

Cause

No power.

• The power plug is disconnected.

• The automatic power off function turned the

The DVD player turned off

by itself.

No picture or abnormal color

• The TV is not set to receive DVD signal

(pinkish, greenish, etc.).

• The video/HDMI cable is not connected

• Mismatch setting between TV and this unit.

• Wrong connection.

• P-Scan mode is selected on a TV equipped

No sound.

• The equipment connected with the audio cable

• The audio cable is not connected securely.

• The audio receiver or TV is turned off.

• The setting of output sound format is

The playback picture has oc-

• The disc is dirty.

casional distortion.

• It is in fast forward or fast reverse playback.

Brightness is unstable or

• The effect of copy protection.

noises are present in the

playback pictures.

The DVD player does not

• No disc is inserted.

start playback.

• An unplayable disc is inserted.

• The disc is placed upside down.

• The disc is not placed within the guide.

• The disc is dirty.

• The parental lock function is set.

Playback does not follow

• It is in the mode of repeat playback, memory

the course of the disc's

program.

Buttons do not work.

• Power supply ﬂ uctuations or other abnormalities

• The remote control is not pointed at the remote

The remote control does not

work properly.

• The remote control is too far from the DVD

• The batteries in the remote control are

unit off.

output.

securely.

with component video input jacks but does

not support progressive scan.

is not set to receive DVD signal output.

incorrect.

playback, etc.

such as static electricity may interrupt correct

operations.

sensor of the DVD player.

player.

exhausted.

Correction

• Connect the power plug securely into the wall outlet.

• Press the PLAY button.

• Select the appropriate video input mode on the TV

so the picture from the DVD player appears on the

TV screen.

• Connect the video/HDMI cable securely into the

appropriate jacks.

• Select the correct Video out setting.

• Check the connection.

• Turn off P-Scan mode.

• Select the correct input mode of the audio receiver

so you can listen to the sound from the DVD player.

• Connect the audio cable securely into the

appropriate jacks.

• Turn on the equipment connected with the audio

cable.

• Select the proper audio setting.

• Remove the disc and clean it.

• Sometimes a small amount of picture distortion

may appear. This is not a malfunction.

• Connect the DVD player directly to the TV. Avoid

connecting the DVD player to a VCR or TV/VCR

combination.

• Insert a disc.

• Insert a playable disc. (Check the disc type and

color system.)

• Place the disc with the playback side down.

• Place the disc correctly inside the guide on the

disc tray.

• Clean the disc.

• Cancel the parental lock function or change the

parental lock level.

• These operations may prevent a proper progress

of the contents.

• Press and hold the ON/STANDBY button on the

front panel for more than about 3 seconds. The

DVD player turns off. Press the button again to turn

it on. If the buttons still do not work, disconnect

the power plug and insert it into the wall outlet

again.

• Point the remote control at the remote sensor of

the DVD player.

• Operate the remote control within about 7 m.

• Replace the batteries with new ones.

Page

11-12

11-15