Pioneer DEH-30MP 설치 매뉴얼 - 페이지 5

{카테고리_이름} Pioneer DEH-30MP에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-30MP 9 페이지.

페이지 인쇄

1. Installation

Note:

Depending on the kind of vehicle, the function

of 3* and 5* may be different. In this case, be

sure to connect 2* to 5* and 4* to 3*.

1. This product

3. Rear output or subwoofer

output

4. Antenna jack

10. Connect leads of the same

color to each other.

11. Cap (1*)

When not using this terminal,

do not remove the cap.

12. Yellow (3*)

13. Yellow (2*)

Back-up

To terminal always supplied

(or accessory)

with power regardless of

ignition switch position.

14. Red (5*)

15. Red (4*)

Accessory

To electric terminal controlled

(or back-up)

by ignition switch (12 V DC)

ON/OFF.

16. Black (ground)

To vehicle (metal) body.

17. ISO connector

Note:

18. Yellow/black

In some vehicles, the ISO connector may be

If you use an equipment with Mute function, wire

divided into two. In this case, be sure to

this lead to the Audio Mute lead on that equipment.

connect to both connectors.

If not, keep the Audio Mute lead free of any

connections.

20. Connecting cords with RCA pin

plugs (sold separately)

2. Front output

6. AUX input jack (3.5 ø)

5. Fuse

Note:

(10 A)

Use a stereo mini plug cable

to connect with auxiliary

equipment.

8. Jack for the Wired Remote Control Adaptors

Please see the Instruction Manual for the

Wired Remote Control Adaptors (sold

separately).

22. Blue/white

To system control terminal of

the power amp (max. 300 mA

12 V DC).

23. System remote control

24. Blue/white (7*)

To Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

25. Blue/white (6*)

26. The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and 7*

when Pin 5 is an antenna control type. In another

type of vehicle, never connect 6* and 7*.

27. Front speaker

28. Left

30. Rear speaker

or subwoofer

19. Speaker leads

: Front left +

White

White/black: Front left ≠

31. Perform these connections when using

: Front right +

the optional amplifier.

Gray

Gray/black : Front right ≠

Green

: Rear left +

or Subwoofer +

32.

Note:

Green/black: Rear left ≠

or Subwoofer ≠

Change the initial setting of this unit (refer

Violet

: Rear right +

or Subwoofer +

to the Operation Manual). The subwoofer

Violet/black: Rear right ≠

or Subwoofer ≠

output of this unit is monaural.

Connecting the Units

21. Power amp

Note:

•

This unit is for vehicles with a 12-volt battery and

(sold separately)

negative grounding. Before installing it in a

recreational vehicle, truck, or bus, check the

21. Power amp

battery voltage.

(sold separately)

•

To avoid shorts in the electrical system, be sure to

disconnect the ≠ battery cable before beginning

installation.

•

Refer to the owner's manual for details on

connecting the power amp and other units, then

make connections correctly.

•

Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

•

Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake

and seat rails. Do not route wiring in places that

get hot, such as near the heater outlet. If the

insulation of the wiring melts or gets torn, there is

a danger of the wiring short-circuiting to the

vehicle body.

•

Do not pass the yellow lead through a hole into

the engine compartment to connect to the battery.

This will damage the lead insulation and cause a

very dangerous short.

•

Do not shorten any leads. If you do, the

protection circuit may fail to work when it

should.

•

Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

•

When replacing the fuse, be sure to only use a

fuse of the rating prescribed on this unit.

•

Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded

or the left and right ≠ speaker leads are common.

27. Front speaker

•

Speakers connected to this unit must be high-

power with minimum rating of 50 W and

impedance of 4 to 8 ohms. Connecting speakers

29. Right

with output and/or impedance values other than

those noted here may result in the speakers

30. Rear speaker

catching fire, emitting smoke or becoming

or subwoofer

damaged.

Fig. 1

Abb. 1

Afb. 1

êËÒ. 1

Connection Diagram (Fig. 1)

•

When this product's source is switched ON, a

control signal is output through the blue/white

1. This product

lead. Connect to an external power amp's system

2. Front output

remote control or the car's Auto-antenna relay

3. Rear output or subwoofer output

control terminal (max. 300 mA 12 V DC). If the

4. Antenna jack

car features a glass antenna, connect to the

5. Fuse (10 A)

antenna booster power supply terminal.

6. AUX input jack (3.5 ø)

•

When an external power amp is being used with

7. Note:

this system, be sure not to connect the blue/white

Use a stereo mini plug cable to connect with

lead to the amp's power terminal. Likewise, do

auxiliary equipment.

not connect the blue/white lead to the power

8. Jack for the Wired Remote Control Adaptors

terminal of the auto-antenna. Such connection

could cause excessive current drain and

Please see the Instruction Manual for the Wired

malfunction.

Remote Control Adaptors (sold separately).

•

To avoid a short-circuit, cover the disconnected

9. Note:

lead with insulating tape. Insulate the unused

Depending on the kind of vehicle, the function of

speaker leads without fail. There is a possibility

3* and 5* may be different. In this case, be sure

of a short-circuit if the leads are not insulated.

to connect 2* to 5* and 4* to 3*.

•

If this unit is installed in a vehicle that does not

10. Connect leads of the same color to each other.

have an ACC (accessory) position on the ignition

11. Cap (1*)

switch, the red lead of the unit should be

When not using this terminal, do not remove the

connected to a terminal coupled with ignition

cap.

switch ON/OFF operations. If this is not done, the

12. Yellow (3*)

vehicle battery may be drained when you are

Back-up (or accessory)

away from the vehicle for several hours.

13. Yellow (2*)

To terminal always supplied with power

regardless of ignition switch position.

14. Red (5*)

Accessory (or back-up)

15. Red (4*)

To electric terminal controlled by ignition switch

(12 V DC) ON/OFF.

16. Black (ground)

No ACC position

To vehicle (metal) body.

ACC position

17. ISO connector

Note:

•

The black lead is ground. Please ground this lead

In some vehicles, the ISO connector may be

separately from the ground of high-current

divided into two. In this case, be sure to connect

products such as power amps.

to both connectors.

If you ground the products together and the

18. Yellow/black

ground becomes detached, there is a risk of

If you use an equipment with Mute function, wire

damage to the products or fire.

this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead free

•

Cords for this product and those for other

of any connections.

products may be different colors even if they

have the same function. When connecting this

product to another product, refer to the supplied

manuals of both products and connect cords that

have the same function.

19. Speaker leads

: Front left +

White

White/black : Front left ≠

Gray

: Front right +

Gray/black : Front right ≠

: Rear left + or Subwoofer +

Green

Green/black : Rear left ≠ or Subwoofer ≠

: Rear right + or Subwoofer +

Violet

Violet/black : Rear right ≠ or Subwoofer ≠

20. Connecting cords with RCA pin plugs (sold

separately)

21. Power amp (sold separately)

22. Blue/white

To system control terminal of the power amp

(max. 300 mA 12 V DC).

23. System remote control

24. Blue/white (7*)

To Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

25. Blue/white (6*)

26. The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and

7* when Pin 5 is an antenna control type. In

another type of vehicle, never connect 6* and 7*.

27. Front speaker

28. Left

29. Right

30. Rear speaker or subwoofer

31. Perform these connections when using the

optional amplifier.

32. Note:

Change the initial setting of this unit (refer to the

Operation Manual). The subwoofer output of this

unit is monaural.