Pioneer DEH-3900MP 설치 매뉴얼 - 페이지 5

{카테고리_이름} Pioneer DEH-3900MP에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-3900MP 9 페이지. Cd rds receiver
Pioneer DEH-3900MP에 대해서도 마찬가지입니다: 운영 매뉴얼 (20 페이지)

페이지 인쇄

1. Installation

Connecting the Units

Note:

Depending on the kind of vehicle, the function

of 3* and 5* may be different. In this case, be

sure to connect 2* to 5* and 4* to 3*.

2. This Product

1. Rear output

3. Antenna jack

4. Fuse (10 A)

7. Connect leads of the same

color to each other.

8. Cap (1*)

Do not remove cap if this

terminal is not in use.

9. Yellow (3*)

10.Yellow (2*)

Connect to the constant

Back-up

(or accessory)

12 V supply terminal.

11. Red (5*)

12. Red (4*)

Accessory

Connect to terminal controlled

(or back-up)

by ignition switch (12 V DC).

13. Black (chassis ground)

Connect to a clean, paint-free

metal location.

14. ISO connector

27. Yellow/black

Note:

If you use an equipment with Mute function, wire

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to

this lead to the Audio Mute lead on that equipment.

connect to both connectors.

If not, keep the Audio Mute lead free of any connections.

16. Connect with RCA cables

(sold separately)

17. Power amp

(sold separately)

5. Wired remote input

Hard-wired remote control adaptor can be

connected (sold separately).

18. Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

19. System remote control

20. Blue/white (7*)

Connect to Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

21. Blue/white (6*)

22. The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and 7*

when Pin 5 is an antenna control type. In another

type of vehicle, never connect 6* and 7*.

23. Left

24. Right

25. Rear Speaker

26.

Perform these connections when using

the optional amplifier.

15. Speaker leads

White:

Front left

White/black: Front left

Gray:

Front right

Gray/black: Front right

Green:

Rear left

Green/black: Rear left

Violet:

Rear right

Violet/black: Rear right

Connecting the Units

Note:

•

Control signal is output through blue/white cable

•

When this unit is installed in a vehicle without

when this unit is powered on. Connect it to an

ACC (accessory) position on the ignition switch,

external power amp's system remote control or

the vehicle's auto-antenna relay control terminal

red cable must be wired to the terminal that can

(max. 300 mA, 12 V DC). If the vehicle is

detect the operation of the ignition key.

Otherwise, battery drain may result.

equipped with a glass antenna, connect it to the

antenna booster power supply terminal.

•

Never connect blue/white cable to external power

amp's power terminal. Also, never connect it to

the power terminal of the auto antenna.

Otherwise, battery drain or malfunction may

result.

•

Black cable is ground. This cable and other prod-

uct's ground cable (especially, high-current prod-

ucts such as power amp) must be wired separate-

ACC position

No ACC position

ly. Otherwise, fire or malfunction may result if

•

Use this unit in other than the following condi-

they are accidentally detached.

tions could result in fire or malfunction.

•

Cord function may differ according to the

— Vehicles with a 12-volt battery and negative

product, even if cord color is the same. When

grounding.

connecting this system, be sure to check all

— Speakers with 50 W (output value) and 4 ohm

manuals and connect cords correctly.

to 8 ohm (impedance value).

•

To prevent short-circuit, overheating or malfunc-

tion, be sure to follow the directions below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhe-

sive tape around them where they lie against

metal parts.

— Place all cables away from moving parts,

such as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker's nega-

tive cables.

ENGLISH

Connection Diagram

16. Connect with RCA cables (sold separately)

17. Power amp (sold separately)

1. Rear output

18. Blue/white

2. This product

Connect to system control terminal of the power

3. Antenna jack

amp (max. 300 mA 12 V DC).

4. Fuse (10 A)

19. System remote control

5. Wired remote input

20. Blue/white (7*)

Hard-wired remote control adaptor can be con-

Connect to auto-antenna relay control terminal

nected (sold separately).

(max. 300 mA 12 V DC).

6. Note:

21. Blue/white (6*)

Depending on the kind of vehicle, the function of

22.The pin position of the ISO connector will differ

3* and 5* may be different. In this case, be sure

depends on the type of vehicle. Connect 6* and

to connect 2* to 5* and 4* to 3*.

7* when Pin 5 is an antenna control type. In

7. Connect leads of the same color to each other.

another type of vehicle, never connect 6* and 7*.

8. Cap (1*)

23. Left

Do not remove cap if this terminal is not in use.

24. Right

9. Yellow (3*)

25. Rear Speaker

Back-up (or accessory)

26. Perform these connections when using the

10. Yellow (2*)

optional amplifier.

Connect to the constant 12 V supply terminal.

27. Yellow/black

11. Red (5*)

If you use an equipment with Mute function,

Accessory (or back-up)

wire this lead to the Audio Mute lead on that

12. Red (4*)

equipment. If not, keep the Audio Mute lead free

Connect to terminal controlled by ignition swich

of any connections.

(12 V DC).

13. Black (chassis ground)

Connect to a clean, paint-free metal location.

14. ISO connector

Note:

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to connect

to both connectors.

15. Speaker leads

White:

Front left +

White/black: Front left ≠

Front right +

Gray:

Gray/black: Front right ≠

Green:

Rear left +

Green/black: Rear left ≠

Rear right +

Violet:

Violet/black: Rear right ≠