Pioneer DEH-3900MP Instrukcja instalacji - Strona 5
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Odbiornik samochodowy Pioneer DEH-3900MP. Pioneer DEH-3900MP 9 stron. Cd rds receiver
Również dla Pioneer DEH-3900MP: Instrukcja obsługi (20 strony)
Drukuj stronę
Connecting the Units
6.
Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
2. This Product
1*
3*
2*
1. Rear output
3. Antenna jack
5*
4*
4. Fuse (10 A)
7. Connect leads of the same
color to each other.
8. Cap (1*)
Do not remove cap if this
terminal is not in use.
9. Yellow (3*)
10.Yellow (2*)
Connect to the constant
Back-up
(or accessory)
12 V supply terminal.
11. Red (5*)
12. Red (4*)
Accessory
Connect to terminal controlled
(or back-up)
by ignition switch (12 V DC).
13. Black (chassis ground)
Connect to a clean, paint-free
metal location.
14. ISO connector
27. Yellow/black
Note:
If you use an equipment with Mute function, wire
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
this lead to the Audio Mute lead on that equipment.
connect to both connectors.
If not, keep the Audio Mute lead free of any connections.
16. Connect with RCA cables
(sold separately)
17. Power amp
(sold separately)
5. Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
18. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
19. System remote control
20. Blue/white (7*)
Connect to Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
21. Blue/white (6*)
22. The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and 7*
when Pin 5 is an antenna control type. In another
type of vehicle, never connect 6* and 7*.
23. Left
24. Right
25. Rear Speaker
25. Rear Speaker
26.
Perform these connections when using
the optional amplifier.
15. Speaker leads
White:
Front left
White/black: Front left
Gray:
Front right
Gray/black: Front right
Green:
Rear left
Green/black: Rear left
Violet:
Rear right
Violet/black: Rear right
Connecting the Units
Note:
•
Control signal is output through blue/white cable
•
When this unit is installed in a vehicle without
when this unit is powered on. Connect it to an
ACC (accessory) position on the ignition switch,
external power amp's system remote control or
the vehicle's auto-antenna relay control terminal
red cable must be wired to the terminal that can
(max. 300 mA, 12 V DC). If the vehicle is
detect the operation of the ignition key.
Otherwise, battery drain may result.
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
•
Never connect blue/white cable to external power
amp's power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
•
Black cable is ground. This cable and other prod-
uct's ground cable (especially, high-current prod-
ucts such as power amp) must be wired separate-
ACC position
No ACC position
ly. Otherwise, fire or malfunction may result if
•
Use this unit in other than the following condi-
they are accidentally detached.
tions could result in fire or malfunction.
•
Cord function may differ according to the
— Vehicles with a 12-volt battery and negative
product, even if cord color is the same. When
grounding.
connecting this system, be sure to check all
— Speakers with 50 W (output value) and 4 ohm
manuals and connect cords correctly.
to 8 ohm (impedance value).
•
To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the bat-
tery before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhe-
sive tape around them where they lie against
metal parts.
— Place all cables away from moving parts,
such as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors
with insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's nega-
tive cables.
ENGLISH
Connection Diagram
16. Connect with RCA cables (sold separately)
17. Power amp (sold separately)
1. Rear output
18. Blue/white
2. This product
Connect to system control terminal of the power
3. Antenna jack
amp (max. 300 mA 12 V DC).
4. Fuse (10 A)
19. System remote control
5. Wired remote input
20. Blue/white (7*)
Hard-wired remote control adaptor can be con-
Connect to auto-antenna relay control terminal
nected (sold separately).
(max. 300 mA 12 V DC).
6. Note:
21. Blue/white (6*)
Depending on the kind of vehicle, the function of
22.The pin position of the ISO connector will differ
3* and 5* may be different. In this case, be sure
depends on the type of vehicle. Connect 6* and
to connect 2* to 5* and 4* to 3*.
7* when Pin 5 is an antenna control type. In
7. Connect leads of the same color to each other.
another type of vehicle, never connect 6* and 7*.
8. Cap (1*)
23. Left
Do not remove cap if this terminal is not in use.
24. Right
9. Yellow (3*)
25. Rear Speaker
Back-up (or accessory)
26. Perform these connections when using the
10. Yellow (2*)
optional amplifier.
Connect to the constant 12 V supply terminal.
27. Yellow/black
11. Red (5*)
If you use an equipment with Mute function,
Accessory (or back-up)
wire this lead to the Audio Mute lead on that
12. Red (4*)
equipment. If not, keep the Audio Mute lead free
Connect to terminal controlled by ignition swich
of any connections.
(12 V DC).
13. Black (chassis ground)
Connect to a clean, paint-free metal location.
14. ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to connect
to both connectors.
15. Speaker leads
White:
Front left +
White/black: Front left ≠
Front right +
Gray:
Gray/black: Front right ≠
Green:
Rear left +
Green/black: Rear left ≠
Rear right +
Violet:
Violet/black: Rear right ≠