Pioneer Super Tuner IIID AVH-P5000DVD 설치 매뉴얼 - 페이지 2

{카테고리_이름} Pioneer Super Tuner IIID AVH-P5000DVD에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer Super Tuner IIID AVH-P5000DVD 8 페이지. Pioneer avh-p5000dvd: install guide
Pioneer Super Tuner IIID AVH-P5000DVD에 대해서도 마찬가지입니다: 설치 매뉴얼 (9 페이지)

페이지 인쇄

Pioneer Super Tuner IIID AVH-P5000DVD 설치 매뉴얼

Connecting the Units

Connecting the power cord

Note:

Wired remote input

Depending on the kind of vehicle, the

Hard-wired remote control adaptor

Gray

function of 3* and 5* may be different.

can be connected (sold separately).

In this case, be sure to connect 2* to 5*

and 4* to 3*.

20 cm

USB input

This product

1.5 m

USB cable (supplied)

Connect leads of the same

Connect to separately sold

color to each other.

Cap (1*)

USB device.

Do not remove cap if this

terminal is not in use.

Yellow (3*)

Yellow (2*)

Fuse (10 A)

Back-up

Connect to the constant 12 V

(or accessory)

supply terminal.

Fuse resistor

Red (5*)

Red (4*)

Accessory

Connect to terminal controlled by

(or back-up)

ignition switch (12 V DC).

Orange/white

Fuse resistor

Connect to lighting switch terminal.

Black (chassis ground)

Connect to a clean, paint-free metal location.

ISO connector

Speaker leads

Front left +

White:

Note:

White/black: Front left ≠

In some vehicles, the ISO connector may be

Gray:

Front right +

divided into two. In this case, be sure to

Gray/black: Front right ≠

connect to both connectors.

Rear left + or subwoofer +

Green:

Green/black: Rear left ≠ or subwoofer ≠

When you connect the separately sold multi-

Violet:

Rear right + or subwoofer +

channel processor (e.g., DEQ-P6600) to this

Violet/black: Rear right ≠ or subwoofer ≠

unit, do not connect anything to the speaker

leads and system remote control

(blue/white).

Dock connector

Connect to separately sold iPod.

Interface cable (e.g., CD-I200)

(sold separately)

80 cm

Tuner box (supplied)

IP-BUS input

IP-BUS cable

(Blue)

Multi-CD player

(sold separately)

Antenna cable

Yellow/black

(supplied)

If you use an equipment with Mute function, wire this lead to the Audio Mute lead on

that piece of equipment. If not, keep the Audio Mute lead free of any connections.

Connection method

1. Clamp the lead.

2. Clamp firmly with

needle-nosed pliers.

Note:

• The position of the parking brake switch depends on the vehicle model. For details,

consult the vehicle Owner's Manual or dealer.

Light green

Used to detect the ON/OFF status of the parking brake. This

lead must be connected to the power supply side of the parking

brake switch.

Blue/white

Parking brake

Connect to system control terminal of the power

Power supply side

switch

amp (max. 300 mA 12 V DC).

Ground side

Blue/white (7*)

Blue/white (6*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

The pin position of the ISO

connector will differ depending

Notes:

on the type of vehicle. Connect

• Change the initial setting of this unit (refer to the Operation

6* and 7* when Pin 5 is an

Manual). The subwoofer output of this unit is monaural.

• When using a subwoofer of 70 W (2 Ω) , be sure to connect with

antenna control type. In other

types of vehicles, never connect

Violet and Violet/black leads of this unit. Do not connect

6* and 7*.

anything to Green and Green/black leads.

When connecting to separately sold power amp

This product

80 cm

Blue/white

Connect to system control terminal of the power

amp (max. 300 mA 12 V DC).

Blue/white (6*)

The pin position of the ISO connector will

differ depending on the type of vehicle.

Connect 6* and 7* when Pin 5 is an antenna

control type. In other types of vehicles, never

connect 6* and 7*.

Rear output or subwoofer output

(REAR/SUBWOOFER/DEQ OUTPUT)

15 cm

Front output

(FRONT OUTPUT)

15 cm

Blue/white (7*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

When you connect the separately sold multi-

channel processor (e.g., DEQ-P6600) to this

unit, do not connect anything to the speaker

leads and system remote control

(blue/white).

When you connect the multi-channel

processor to this unit, refer to multi-channel

processor's installation manual for the

connection method.

Note:

• Change the initial setting of this unit (refer to the Operation

ENGLISH

Power amp

(sold separately)

Power amp

(sold separately)

Connect with RCA cables

(sold separately)

System remote control

Left

Right

Front speaker

≠

Rear speaker

or subwoofer

≠

Perform these connections when

using the optional amplifier.

Manual). The subwoofer output of this unit is monaural.