Pioneer Super Tuner IIID AVH-P5000DVD Посібник з монтажу - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник з монтажу для Автомобільний приймач Pioneer Super Tuner IIID AVH-P5000DVD. Pioneer Super Tuner IIID AVH-P5000DVD 8 сторінок. Pioneer avh-p5000dvd: install guide
Також для Pioneer Super Tuner IIID AVH-P5000DVD: Посібник з монтажу (9 сторінок)
Друкувати сторінку
Connecting the Units
Connecting the Units
Connecting the power cord
Note:
Wired remote input
Depending on the kind of vehicle, the
Hard-wired remote control adaptor
Gray
function of 3* and 5* may be different.
can be connected (sold separately).
In this case, be sure to connect 2* to 5*
and 4* to 3*.
1*
20 cm
USB input
3*
2*
This product
1.5 m
5*
4*
USB cable (supplied)
Connect leads of the same
Connect to separately sold
color to each other.
Cap (1*)
USB device.
Do not remove cap if this
terminal is not in use.
Yellow (3*)
Yellow (2*)
Fuse (10 A)
Back-up
Connect to the constant 12 V
(or accessory)
supply terminal.
Fuse resistor
Red (5*)
Red (4*)
Accessory
Connect to terminal controlled by
(or back-up)
ignition switch (12 V DC).
Orange/white
Fuse resistor
Connect to lighting switch terminal.
Black (chassis ground)
Connect to a clean, paint-free metal location.
ISO connector
Speaker leads
Front left +
White:
Note:
White/black: Front left ≠
In some vehicles, the ISO connector may be
Gray:
Front right +
divided into two. In this case, be sure to
Gray/black: Front right ≠
connect to both connectors.
Rear left + or subwoofer +
Green:
Green/black: Rear left ≠ or subwoofer ≠
When you connect the separately sold multi-
Violet:
Rear right + or subwoofer +
channel processor (e.g., DEQ-P6600) to this
Violet/black: Rear right ≠ or subwoofer ≠
unit, do not connect anything to the speaker
leads and system remote control
(blue/white).
Dock connector
Connect to separately sold iPod.
Interface cable (e.g., CD-I200)
(sold separately)
80 cm
Tuner box (supplied)
IP-BUS input
IP-BUS cable
(Blue)
Multi-CD player
(sold separately)
Antenna cable
Yellow/black
(supplied)
If you use an equipment with Mute function, wire this lead to the Audio Mute lead on
that piece of equipment. If not, keep the Audio Mute lead free of any connections.
Connection method
1. Clamp the lead.
2. Clamp firmly with
needle-nosed pliers.
Note:
• The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner's Manual or dealer.
Light green
Used to detect the ON/OFF status of the parking brake. This
lead must be connected to the power supply side of the parking
brake switch.
Blue/white
Parking brake
Connect to system control terminal of the power
Power supply side
switch
amp (max. 300 mA 12 V DC).
Ground side
Blue/white (7*)
Blue/white (6*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
The pin position of the ISO
connector will differ depending
Notes:
on the type of vehicle. Connect
• Change the initial setting of this unit (refer to the Operation
6* and 7* when Pin 5 is an
Manual). The subwoofer output of this unit is monaural.
• When using a subwoofer of 70 W (2 Ω) , be sure to connect with
antenna control type. In other
types of vehicles, never connect
Violet and Violet/black leads of this unit. Do not connect
6* and 7*.
anything to Green and Green/black leads.
When connecting to separately sold power amp
This product
80 cm
Blue/white
Connect to system control terminal of the power
amp (max. 300 mA 12 V DC).
Blue/white (6*)
The pin position of the ISO connector will
differ depending on the type of vehicle.
Connect 6* and 7* when Pin 5 is an antenna
control type. In other types of vehicles, never
connect 6* and 7*.
Rear output or subwoofer output
(REAR/SUBWOOFER/DEQ OUTPUT)
15 cm
Front output
(FRONT OUTPUT)
15 cm
Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
When you connect the separately sold multi-
channel processor (e.g., DEQ-P6600) to this
unit, do not connect anything to the speaker
leads and system remote control
(blue/white).
When you connect the multi-channel
processor to this unit, refer to multi-channel
processor's installation manual for the
connection method.
Note:
• Change the initial setting of this unit (refer to the Operation
<ENGLISH>
ENGLISH
Power amp
(sold separately)
Power amp
(sold separately)
Connect with RCA cables
(sold separately)
System remote control
Left
Right
+
+
Front speaker
Front speaker
≠
≠
+
+
Rear speaker
Rear speaker
or subwoofer
or subwoofer
≠
≠
Perform these connections when
using the optional amplifier.
Manual). The subwoofer output of this unit is monaural.