Pioneer VSX-422-S 사용 설명서 - 페이지 30
{카테고리_이름} Pioneer VSX-422-S에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer VSX-422-S 36 페이지. Pioneer av receiver operating instructions
Pioneer VSX-422-S에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (45 페이지)
페이지 인쇄
6
6
4
Confirm your selected setup option.
The test tones will start after you press ENTER. After the
volume increases to the reference level, test tones will be
output.
2c.Channel Level
Test Tone
[ Manual ]
Please Wait . . .20
Caution
Loud test tones
will be output.
Return
5
Adjust the level of each channel using /.
/
If you selected Manual, use
to switch speakers. The
Auto setup will output test tones in the order shown on-
screen:
2c.Channel Level
0dB
Front L
Center
[
0dB]
Front R
[
0dB]
Surround R
[
0dB]
Surr. Back R
[
–––
]
Surr. Back L
[
–––
]
Surround L
[
0dB]
Subwoofer
[
0dB]
Return
Adjust the level of each speaker as the test tone is
emitted.
Note
•
If you are using a Sound Pressure Level (SPL) meter, take
the readings from your main listening position and adjust
the level of each speaker to 75 dB SPL (C-weighting/slow
reading).
•
The subwoofer test tone is output at low volumes. You may
need to adjust the level after testing with an actual
soundtrack.
6
When you're finished, press RETURN.
You return to the Manual SP Setup menu.
Tip
•
You can change the channel levels at any time by press
, then press
and
CH SELECT
RECEIVER
remote control. You can also press
CH SELECT
to select the channel, and then use
channel levels.
Speaker Distance
For good sound depth and separation from your system, you
need to specify the distance of your speakers from the
listening position. The receiver can then add the proper delay
needed for effective surround sound.
•
For the assignment of the digital signal inputs, see
Selecting the audio input signal on page
1
Select 'Manual SP Setup' from the Home Menu.
2
Select 'Speaker Distance' from the Manual SP Setup
menu.
2d.Speaker Distance
2.Manual SP Setup
a.Speaker Setting
Front L
Center
b.X.Over
c.Channel Level
Front R
d.Speaker Distance
Surround R
Surr. Back R
Surr. Back L
Surround L
Subwoofer
Return
3
Adjust the distance of each speaker using /.
You can adjust the distance of each speaker in 0.1 m
increments.
4
When you're finished, press RETURN.
You return to the Manual SP Setup menu.
30
The Input Assign menu
ANALOG IN1 audio input terminal is assigned to CD under
on the
factory settings, but this can be changed to TV input.
LEV +/–
and use
/
1
Select 'Input Assign' from the Home Menu.
/
to adjust the
2
19.
Select 'Analog Input' from the Input Assign menu.
3.Input Assign
a.Analog Input
3.0 m
[
]
3.0 m
[
]
3.0 m
[
]
3.0 m
[ ––––
]
3
[ ––––
]
Select the desired input option for the ANALOG IN1
[
]
3.0 m
[
]
3.0 m
audio input terminal.
Return
4
When you're finished, press RETURN.
You return to the Input Assign menu.
Home Menu
Ho me Me nu
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
5.Auto Power Down
6.FL Demo Mode
7.HDMI Setup
Re turn
3a.Analog Input
Analog
CD
Return
Return