Pioneer S-7EX XTW/E 사용 설명서 - 페이지 3

{카테고리_이름} Pioneer S-7EX XTW/E에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer S-7EX XTW/E 24 페이지. Ex series
Pioneer S-7EX XTW/E에 대해서도 마찬가지입니다: 카탈로그 (20 페이지), 브로셔 및 사양 (16 페이지), 서비스 매뉴얼 (10 페이지)

페이지 인쇄

• Do not place the speaker where it will be in direct

sunlight, and avoid positioning it near heaters and air

conditioners. This may cause warping and discoloration

of the speaker cabinet and damage the speaker.

• Pioneer assumes no liability whatsoever for damages

resulting from assembly, improper mounting, insuffi-

cient reinforcement, misuse of the product, acts of

nature, etc.

Using the speaker base

Included with this speaker system is a speaker base for

better sound, stability and safety. Place the speaker on the

base as shown below.

Using the spikes

This speaker system includes spikes that you can use to

isolate the speaker from the floor. Spikes are recommended

when placing the speaker on a thick carpet (for added

stability), or for better sound when placing the speaker on a

hard reverberant surface (such as a concrete or wood floor).

Use the supplied spike pads to avoid scratching the floor or

other surface where the speaker is placed.

Speaker

base bottom

Attach the spikes to the nuts provided.

Attach all four spikes to the threaded metal inserts

at the bottom of the speaker base.

Choose the location for speaker placement then put

the spike bases on the floor.

Place the stand so that the spikes are resting on the

spike bases on the floor.

Before placing the speaker on the speaker base, make sure

the base is stable and resting squarely on all four spikes.

Caution: when using the spikes

• Note that these spikes are sharp metal and can cause

damage to flooring. Make sure to lay down a cloth or

suitable base before setting up.

Spike

Nut

Connecting to an amplifier

Before connecting to your amplifier, make sure that the amp is

switched off.

This speaker does not include speaker cables used for

connecting to a stereo. Note the following when selecting

speaker cables.

• Use heavy-gauge speaker cable if possible, and keep the

cables to the minimum necessary length.

• Cables have differing characteristics. Keep this in mind

when using any cable.

• Select cables with as little resistance as possible, and

make sure the cables to the speaker terminals and amp

are firm and secure.

CAUTION

These speaker terminals carry HAZARDOUS LIVE

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

Connecting the cables

Switch off the power to your amplifier.

Connect the speaker cables to the input terminals

(lower) on the back of the speaker. For input terminal

polarity, red is positive (+) and black is negative (–).

Grasp the cap knobs on the lower input terminals and rotate

them to the left (counter-clockwise), insert the speaker cable

wires into the holes in the terminal posts, then tighten the

knobs to secure the short bar as well as the wires.

• You can also use banana plugs for this connection. To do

so, you must first remove the caps from the terminal

posts.

Short bar connectors

Black terminal ( )

Connect the other ends of the cables to the amp's

speaker output terminals (for more details, refer to your

amp owner's manual).

• After connecting the plugs, pull lightly on the cables to

make sure that the ends of the cables are securely

connected to the terminals. Poor connections can

create noise and interruptions in the sound.

• If the cables' wires happen to be pushed out of the

terminals, allowing the wires to come into contact with

each other, it places an excessive additional load on the

amp. This may cause the amp to stop functioning, and

may even damage the amp.

D3-4-2-2-3_A_En

Red terminal ( )