Whirlpool CABRIO WED8200YW2 사용 및 관리 매뉴얼 - 페이지 14

{카테고리_이름} Whirlpool CABRIO WED8200YW2에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool CABRIO WED8200YW2 36 페이지. Electronic dryer

페이지 인쇄

First t rythesolutions suggested here orvisitourwebsite a twww.whirlpool.com/help

if you experience

for assistance and to possibly avoid a service call.

Possible Causes

Solution

Clothes are not drying

The load is too large and heavy

Separate the load to tumble freely.

satisfactorily

or drying

to dry quickly.

times are too long

Fabric softener sheets are blocking

The air outlet grille is just inside the door, behind the lint

the grille,

screen. Check that it is not blocked by a fabric softener sheet.

Use only one fabric softener sheet, and use it only once.

The dryer is located in a room with

Proper operation of dryer cycles requires temperatures

above

temperature

below 45°F (7°C).

45°F (7°C).

The dryer is located in a closet.

The load may not be contacting

the

sensor strips on Automatic

Cycles.

Clothes are coming out of the

Steam cycles with damp or wet

spots.

Cycle time is too short

The Automatic

Cycles are ending

early.

Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum

of 1" (25 mm) of airspace, and, for most installations, the

rear of the dryer requires 5" (127 mm). See "installation

Instructions".

Level the dryer. See "installation

Instructions".

All four dryer

feet should be in firm contact with the floor.

Under certain environmental

or installation conditions you

may experience underdrying.

Select the Quick Refresh cycle.

Then select the appropriate time based on the load to be

refreshed.

Change the dryness level setting on Automatic Cycles.

Increasing or decreasing the dryness level will change the

amount of drying time in a cycle, if loads are consistently

ending too early, see also "Changing the Automatic

Cycle

settings to increase drying time".

Lint on load

Lint screen is clogged with lint.

Clean lint screen before each load.

Stains on load

Improper use of fabric softener.

Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can

stain your garments. Do not use fabric softener sheets with

Steam Cycles.

Stains on drum

Loose dyes in clothes.

Drum stains are caused by dyes in clothing (usually blue

jeans). These will not transfer to other clothing.

Loads are wrinkled

The load was not removed from

dryer at the end of the cycle.

The dryer was overloaded.

For steam cycles, the water is not

properly connected with the dryer.

Select Enhanced Touch Up or Quick Refresh cycles (on some

models) to tumble the load with water and heat. These cycles

are best for smoothing out wrinkles and reducing odors from

loads consisting

of wrinkle-free

cotton, cotton polyester

blends, common knits, and synthetic garments.

NOTE: Refer to garment care label instructions. Dry clean

only garments are not recommended.

Dry smaller loads that can tumble freely. When using

the Enhanced Touch Up cycle, be sure to select the correct

number of garments to be refreshed. Results may also vary

depending on fabric type. This cycle is best for reducing

wrinkles and odors from loads consisting of

wrinkle-free cotton, cotton polyester blends, common knits,

and synthetics.

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer's water

inlet valve. Check that the water supply is turned on.