Whirlpool CED9160GW 설치 지침 매뉴얼 - 페이지 13
{카테고리_이름} Whirlpool CED9160GW에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool CED9160GW 32 페이지. Commercial front-load washer
페이지 인쇄
CODE
J. Cd COIN/DEBIT OPTION
J.
Cd
Both coin and debit selected. Press the COLD button
3 consecutive times for this selection (default for
9150 models).
J.
C_
Coins selected, debit disabled. Press the COLD
button 3 consecutive times for this selection.
J.
_d
Debit card selected, coins disabled. Press the COLD
button 3 consecutive times for this selection (default
for 9160 models).
J.
Ed
Enhanced Debit is self-selected when a Generation 2
card reader is installed in the washer. The Ed option
cannot be manually selected or deselected.
g
Press the WARM button once to advance
to next code.
L. 00
PRICE SUPPRESSION OPTION
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'. This option causes the customer
display to show 'AVAILABLE' or 'ADD' rather than
the amount of money to add (used mainly in debit
installations).
L. 00
Not Selected 'OFF'.
L. PS
Selected 'ON'. Press the COLD button once for this
selection.
Press the WARM button once to advance
g
to next code.
n. CE CLEAR ESCROW OPTION
When selected, money held in escrow for
30 minutes without further escrow or cycle
activity will be cleared.
n.
00
Not Selected 'OFF'.
CE
Selected 'ON'. Press the COLD button once for
n.
this selection.
g
Press the WARM button once to advance to
next code.
U. 00
PENNY INCREMENT OFFSET
U. 00
This represents the penny increment price offset
used with Generation 2 (Enhanced Debit) card
readers. Choose from 0–4 pennies by pressing
the HOT button.
g
Press the WARM button once to advance
to next code.
A1. 00
PREWASH LENGTH
A1. 00
This is the number of minutes of PREWASH. Choose
0 to disable the prewash or select between 2 and 7
minutes by pressing the HOT button.
g
Press the WARM button once to advance
to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00
Represents the number
of cycles in HUNDREDS
2 00
Represents the number
of cycles in ONES
EXPLANATION
1 02 =
2 25 =
TOTAL CYCLES =
This is "VIEW ONLY" and cannot be cleared.
Press the WARM button once to advance to next code.
If money counter (1.0C or 1.C0) is selected, the following
is true:
3 00
Number of dollars
in HUNDREDS
4 00
Number of dollars in ONES
5 00
Number of CENTS
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
CHW9150 Models:
Reinstall access door.
CHW9160 Models:
1. Unplug washer or disconnect power.
2. Open console, reinsert plug into AA1, and close console.
3. Plug in washer or reconnect power.
MODEL CHW9150 SET UP AS PN WITH PROGRAMMING
SWITCH:
Turn key clockwise and remove.
MODEL CHW9160 SET UP AS PN WITHOUT PROGRAMMING
SWITCH:
Set-up mode can be exited by using procedures from "Service
Access Code."
SERVICE ACCESS CODE
This code can be entered to access service mode without
removing the console. It only functions on washers set up for 0
vend price without any Special Pricing setup, and the Coin/Debit
Option must be set to "J._d". If the washer is not in failure mode,
the door must be opened to proceed. Service Access Code
contains 4 steps. Perform the following steps:
1. Press the upper left button.
2. Press the lower right button.
3. Press the upper right button.
4. Press the lower left button.
NOTE: If the Service Access Code procedure is not completed
properly, as noted above, there is a 15-second delay before it can
be attempted again.
There are 3 options to exit from the Service Mode:
1. From Set-up Code 8, press button #1 for 4 seconds.
2. Wait 2 minutes without touching any buttons (without
diagnostic modes running).
3. Power down the washer; then reapply power.
200
25
225
3 01 = $100.00
4 68 = $ 68.00
5 75 = $
.75
TOTAL = $168.75
13