Whirlpool Duet Steam WED94HEX 설치 지침 매뉴얼 - 페이지 13

{카테고리_이름} Whirlpool Duet Steam WED94HEX에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool Duet Steam WED94HEX 16 페이지. Electronic dryer
Whirlpool Duet Steam WED94HEX에 대해서도 마찬가지입니다: 치수 매뉴얼 (2 페이지), 사양 (1 페이지), 사용 및 관리 매뉴얼 (40 페이지)

페이지 인쇄

A. Standard rear offset exhaust installation

B. Left or right side exhaust installation

C. Bottom exhaust installation

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for

your installation. Two examples of close-clearance installations are

shown. Refer to the manufacturer's instructions.

A. Over-the-top installation (also available with one offset elbow)

B. Periscope installation

NOTE: The following kits for close-clearance alternate installations

are available for purchase. Please see the "Assistance or Service"

section to order.

■

Over-the-Top Installation:

Part Number 4396028

■

Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 4396037 - 0" (0 mm) to 18" (457 mm) mismatch

Part Number 4396011 - 18" (457 mm) to 29" (737 mm)

mismatch

Part Number 4396014 - 29" (737 mm) to 50" (1.27 m) mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path

■

Select the route that will provide the straightest and most direct

path outdoors.

■

Plan the installation to use the fewest number of elbows and

turns.

■

When using elbows or making turns, allow as much room as

possible.

■

Bend vent gradually to avoid kinking.

■

Use the fewest 90° turns possible.

Determine vent length and elbows needed for best

drying performance

■

Use the following vent system chart to determine type of vent

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the

Vent system chart.

Exhaust systems longer than those specified will:

■

Shorten the life of the dryer.

■

Reduce performance, resulting in longer drying times and

increased energy usage.

The vent system chart provides venting requirements that will help

to achieve the best drying performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90º turn inside

the dryer. To determine maximum exhaust length, add one 90º turn

to the chart.

Number 90º

Type of vent

elbows

Rigid metal

Install Vent System

1. Install exhaust hood. Use caulking compound to seal exterior wall

opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust hood.

Secure vent to exhaust hood with 4" (102 mm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See "Determine vent path" in "Plan Vent System." Avoid 90º

turns. Use clamps to seal all joints. Do not use duct tape,

screws, or other fastening devices that extend into the

interior of the vent to secure the vent, because they can catch

lint.

INSTALL LEVELING LEGS

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. To avoid damaging the floor, use a large flat piece of cardboard

from the dryer carton. Place cardboard under the entire back

edge of the dryer.

Box /louvered

Angled

hoods

64ft (20 m)

58ft (17.7 m)

54 ft (16.5 m)

48 ft (14.6 m)

44 ft (13.4 m)

38 ft (11.6 m)

35 ft (10.7 m)

29 ft (8.8 m)

27 ft (8.2 m)

21 ft (6.4 m)