Whirlpool WGD9400SW1 사용 및 관리 매뉴얼 - 페이지 15

{카테고리_이름} Whirlpool WGD9400SW1에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool WGD9400SW1 48 페이지. Electronic gas dryer
Whirlpool WGD9400SW1에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (32 페이지)

페이지 인쇄

•

Press and hold START button until dryer starts (about

1 second).

Once an Automatic

cycle has started, the WRINKLE

SHIELD

feature and cycle signals can be adjusted. Press

the PAUSE/CANCEL key twice to stop the dryer and clear the

settings, allowing you to select another cycle and Dryness

Level.

NOTE: Time and Temperature are not adjustable for

Automatic Cycles. Pressing the DRY TIME or TEMPERATURE

buttons will cause a triple beep, indicating that the time

cannot be changed.

How Automatic Cycles Work

The AccelerCare

function improves drying performance

with Auto Moisture Sensing Plus, which advances the cycle

as moisture is extracted from clothing. A thermistor

(electronic temperature sensor) and moisture sensing strips in

the dryer drum help measure the amount of moisture in the

clothes as they tumble. An electronic control determines the

load type to help save time, avoid overdrying, and increase

the accuracy of the end dryness level. After the first 5 minutes

of an automatic cycle, the estimated time display will adjust

based on the approximate

load size, cycle, dryness level

selected and amount of moisture left in the clothes. When the

clothes have reached approximately

80% of the dryness level

selected, the estimated time display will adjust again,

showing the final drying time. The AccelerCare

feature

takes the guesswork out of drying time and enhances fabric

care.

To use a Manual Cycle

NOTE: A light next to each feature will glow green when the

feature is selected or will glow amber when the feature is

selectable. The light will not glow when the selection is

unavailable with the cycle or option combinations

selected.

•

Press POWER.

Rotate the dial to select a Manual Cycle.

Press the DRY TIME up or down buttons until the desired

drying time is displayed. Press DRY TIME, and the time

will change by 1-minute intervals. Press and hold DRY

TIME, and the time will change by 5-minute intervals. The

initial time displayed is the actual drying time.

Ad)ust M anual

Dry Time

@®

The Dry Time feature can be used only with Manual

Cycles.

Press TEMPERATURE until the desired temperature

glows green.

High

Medium

Low

ExtraL0w

Air 0nly

Temperature

Adjust M_noal

Cycles O/lly

Temperature settings can be changed only with Manual

Cycles.

Press the WRINKLE SHIELD

feature button if this

option is desired.

Press the CYCLE SIGNAL button to set end of cycle

signal volume to desired level.

•

Press and hold START button until dryer starts (about

1 second).

NOTE: Dryness Level is not adjustable for Manual Cycles.

Pressing the Dryness Level button will cause the triple beep

indicating that this option is not selectable.

While a Manual Cycle is running, you can change the settings

for Time, Temperature, the WRINKLE SHIELD

feature and

the cycle signals. Press the PAUSE/CANCEL key twice to

stop the dryer and clear the settings, allowing you to select

another cycle.

To stop your dryer at any time

Press PAUSE/CANCELtwice or open the door.

To pause the dryer at any time

Open the door or press PAUSE/CANCEL once.

To restart the dryer

Close the door and press and hold START button until dryer

starts.

NOTE: Drying will continue from where the cycle was interrupted,

if you close the door and press Start within 5 minutes. If the cycle

is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

This feature allows you to lock your settings to avoid unintended

use of the dryer. You can also use the Control Locked feature to

avoid unintended cycle or option changes during dryer operation.

To enable the Control

Locked feature when dryer is

running:

Press and hold the CONTROL LOCK/UNLOCK

button for

3 seconds. The control is locked when a single beep is heard and

the Control Locked status light is on.

•

When the dryer is off, it is not necessary to press the Control

On button before activating the Control Locked feature.

To unlock:

Press and hold the CONTROL LOCK/UNLOCK

button for

3 seconds to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the

dryer can be stopped by pressing the Pause/Cancel button, but

cannot be restarted until the control is unlocked.

Select the correct cycle and dryness level or temperature for your

load. If an Automatic Cycle is running, the display shows the

estimated cycle time when your dryer is automatically

sensing

the dryness level of your load. If a Manual Cycle is running, the

display shows the exact number of minutes remaining in the

cycle.

Cool Down tumbles the load without heat during the last few

minutes of all cycles. Cool Down makes the loads easier to

handle and reduces wrinkling. The length of the Cool Down

depends on the load size and dryness level.

Drying tips

•

Follow care label directions when they are available.

•

If desired, add a fabric softener sheet. Follow package

instructions.

•

Remove the load from the dryer as soon as tumbling stops to

reduce wrinkling. This is especially important for permanent

press, knits and synthetic fabrics.