Check operation
Electronic ignition system
Cooktop and oven burners use electronic
ignitors in place of standing pilots. When a
cooktop control knob is turned to the "LIGHT"
position, the system creates a spark to light
the burner. This sparking continues until the
control knob is turned to the desired setting.
When the oven control is turned to the desired
setting, a hot surface ignitor heats to a bright
orange and ignites the gas. No sparking
occurs. The glow bar remains on while
the burner operates.
Check operation of cooktop
15
n
Push in and turn each surface unit
control knob to "LIGHT" position. The flame
should light within 4 seconds. Turn control
knob to "HIGH" position after burner lights.
Check each cooktop burner for proper flame.
The small inner cone should have a very
distinct blue flame l/4" to l/2" long. The outer
cone is not as distinct as the inner
cone. If the flame is noisy or
blowing, it is getting too much air.
If the flame is soft and lazy, it is not
getting enough air. Turn surface
burner control knobs to "OFF"
position. Adjust air shutter if
needed.
lf surface burners need adjusting:
1. Lift up cooktop maintop until it is held in
place by support rods.
r shutter
2.Adjust the air shutter for each burner by hand
as needed. Close the air shutter to decrease
the amount of air to the flame. Open the air
shutter to increase the amount of air to the
flame. Adjust the air shutter to the widest
opening that will not cause the flame to lift or
blow off of the burner.
3. Repeat the first part of Step 15 after adjusting
the air shutters.
Check operation of oven burner
16
w Open oven door.
Remove oven bottom:
Remove two screws at the rear of the oven
bottom. Lift the rear of the oven bottom up and
back until the front of the panel is away from
the front frame. Remove from oven.
You can check the burner flame by removing the
flame spreader or by using a mirror.
Remove flame spreader:
Remove two screws from the front tabs of the
flame spreader. Lift front of the flame spreader
and pull forward to remove tabs from rear of
oven.
Using a mirror:
Insert mirror to one side of the burner. Look into
mirror to check flame.
17
n
Follow the instructions for your type
of oven controls.
,m
OPP ovm mm PI-eC*INC,
CLEAN.
OVEN HEATING
0
"zmrn
DOOR LOCKED/CLEANING
0
BROIL
.
,CLoSP mall w_
FLLs"1NGi
Push in and turn the oven selector control knob
to "350°F." The oven burner should light in 50-60
seconds; this delay is normal. The oven valve
requires a certain time before it will open and
allow gas to flow.
If your oven has electronic control pads only:
1. Press the "BAKE" pad.
l
The "BAKE" indicator will light.
l
"350" will appear in the display.
2. Press the START/ENTER pad.
l
The "HEAT" and "ON" indicators will light.
. The oven burner should light in 50-60
seconds; this delay is normal. The oven
valve requires a certain time before it will
open and allow gas to flow.
To avoid damaging the hot surface ignitor,
do Not insert any object into the openings of
the protective shield that surrounds the ignitor
or clean that area.
18
w Check the oven burner for
proper flame. The flame should be l/2"
long, with inner cone of bluish-green,
and outer mantle of dark blue, and
should be clean and soft in character. No yellow
tips, blowing or lifting of flame should occur. If
burner does not light, check that the regulator
shutoff valve is in the "on" position (see Step
11).
shutoff
valve
and screw
If oven flame needs adjusting:
Locate the air shutter next to the pressure
regulator. Loosen screw and adjust the air
shutter until the proper flame appears. Tighten
screw.
19
n
Turn the control knob to "OFF" or
press the "OFF/CANCEL" pad.
20
n
Replace flame spreader, oven botton
and oven racks.
Check operation of oven broil
burner
21
n
Follow the instructions for your type
of oven controls.
OFF
iwl:"
ml
illiN
OVEN ON 0
<l"RN wr YEN WHM FIdWINSI
CLEAN .
OVEN HEATING 0
"k;p
DOOR LOCKED/CLEANING
0
BROIL .
ILL -E ://ImlR wm PLL-IIINC,
Push in and turn the oven selector control knob
to "BROIL." The broil burner should light in 50-
60 seconds; this delay is normal. The oven valvi
requires a certain time before it will open and
allow gas to flow.
1. Press the "CUSTOM BROIL" pad.
l
"525" or "HI" will appear in the display.
l
The "BROIL" indicator will light.
2. Press the "START/ENTER" pad.
l
"HEAT" and "ON" indicators will light.
l
The oven burner should light in 50-60
seconds; this delay is normal. The oven
valve requires a certain time before it will
open and allow gas to flow.
22
w Check the broil burner for
proper flame. The flame should be l/2"
long, with inner cone of bluish-green,
and outer mantle of dark blue, and
should be clean and soft in character.
No yellow tips, blowing or lifting of
flame should occur.
If flame needs to be adjusted:
Loosen the lock screw on the air shutter locatec
at the rear of the broil burner. Adjust the air
shutter as needed. Tighten lock screw.
23
n
Turn the oven control knob to "OFF"
or press the "OFF/CANCEL" pad.
Paae 6
페이지 인쇄