Whirlpool 30 " Eye-Level Gas Range 설치 지침 매뉴얼 - 페이지 7

{카테고리_이름} Whirlpool 30 " Eye-Level Gas Range에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 30 " Eye-Level Gas Range 10 페이지. Freestanding gas range with self-cleaning oven
Whirlpool 30 " Eye-Level Gas Range에 대해서도 마찬가지입니다: 설치 지침 및 사용 및 관리 설명서 (32 페이지), 설치 지침 매뉴얼 (11 페이지), 설치 지침 및 사용 및 관리 매뉴얼 (28 페이지), 설치 지침 매뉴얼 (11 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (28 페이지), 설치 지침 매뉴얼 (48 페이지), 설치 지침 매뉴얼 (32 페이지), 설치 지침 매뉴얼 (12 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 매뉴얼 (7 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (7 페이지)

페이지 인쇄
Whirlpool 30
Gas conversions (from Natural gas to L.P. gas; or
from L.P. gas to Natural gas) must be done
by
a
qualified installer.
Fire Hazard
Shut off gas supply line valve.
Make all conversions
before turning gas
supply valve back on.
Failure to follow these instructions
could
result in explosion, fire or other injury.
L.F? gas conversion
1
n
Complete installation sections A-C (Pages
4-5) before converting cooktop to L.P. gas. Check
that main gas supply line has been shut off and
the power supply cord is disconnected.
2
w Remove burner grates.
pressure
regulator
pressure
regulator
cover
cap
-washer
-
Nat. gas
L.P. gas
DO NOT REMOVE THE PRESSURE REGULATOR.
3
H Open broiler drawer to locate pressure
regulator.
Pressure regulator: Remove plastic cover. Turn
cap marked "N" on front of pressure regulator
counterclockwise
with a wrench to remove. Do
Not disturb or remove the spring beneath the
cap. Turn the cap over and reinstall cap on
regulator so that the letters "L.P." are visible.
Replace plastic cover over cap.
shipping
screw
air shutter
\
4
n
Cooktop burners: Lift up cooktop maintop
until it is held in place by support rods. Remove
shipping screws from each burner. Remove
burners.
orifice spuds
NAT
L.P.
etches
gas
manifold
L.R.
L.F.
A.F.
R.R.
5
H Locate L.P. gas orifice spuds in a literature
package included with the range. All L.P. gas
orifice spuds are stamped with "66". Remove
Natural gas orifice spuds using a 3/8"
combination wrench. Install L.P. gas orifice
spuds to replace the Natural gas orifice spuds.
Place Natural gas orifice spuds in plagtic parts
bag for future use and keep with literature
package. Reinstall burners. Lower ma~intop to
operating position. Reinstall burner grates.
pre-set at factory
for Natural gas
6
H Oven burner: Use l/2" combination
wrench to turn the orifice hood down snug onto
pin (approximately
2 to 2-l/2 turns). DO NOT
OVERTIGHTEN. The burner flame can'not be
properly adjusted if this conversion is not made.
hood
-
\\
I
7
n
Broil burner: Use l/2" combination
wrench
to turn the orifice hood down snug onto pin
(approximately
2 to 2-l/2 turns). DO NOT
OVERTIGHTEN. The burner flame cannot be
properly adjusted if this conversion is not made.
8
w Complete installation sections D through
E, Pages 5-6. Check for proper flame. The small
inner cone should have a very distinct blue flame
l/4' to l/2" long. The outer cone is not as distinct
as the inner cone. L.P. gas flames have a slightly
yellow tip. If the flame is noisy or blowing, it is
getting too much air. If the flame is soft and lazy,
it is not getting enough air.
Page 7