Whirlpool 30" (76.2 cm) Cooktop 매뉴얼 - 페이지 6

{카테고리_이름} Whirlpool 30" (76.2 cm) Cooktop에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 30" (76.2 cm) Cooktop 28 페이지. 30" (76.2 cm) wall-mount canopy range hood
Whirlpool 30" (76.2 cm) Cooktop에 대해서도 마찬가지입니다: 설치 및 사용 설명서 (24 페이지), 사용 및 관리 매뉴얼 (16 페이지)

페이지 인쇄

Example Vent System

90 elbow

6 ft (1.8 m)

2 ft

(0.6 m)

The following example falls within the maximum vent length of

35 ft (10.7 m).

1 - 90° elbow

= 5.0 ft (1.5 m)

1 - wall cap

= 0.0 ft (0.0 m)

8 ft (2.4 m) straight

= 8.0 ft (2.4 m)

System length

= 13 ft (3.9 m)

Electrical Requirements

IMPORTANT: Observe all governing codes and ordinances. Save

Installation Instructions for electrical inspector's use.

It is the customer's responsibility to contact a qualified electrical

installer, and to ensure that the electrical installation is adequate

and in conformance with National Electrical Code, ANSI/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

It is recommended that the vent system be installed before

hood is installed.

Do not cut a joist or stud unless absolutely necessary. If a

joist or stud must be cut, then a supporting frame must be

constructed.

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

Check your ceiling height and the hood height maximum

before you select your hood.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

1. If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to rear

wall. Otherwise, put a thick, protective covering over

countertop, cooktop or range to protect from damage or dirt.

Wall cap

INSTALLATION INSTRUCTIONS

Prepare Location

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A 120 Volt, 60 Hz., AC only 15-amp fused, electrical circuit is

required.

Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure range

hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

The range hood must be connected with copper wire only.

The range hood should be connected directly to the fused

disconnect (or circuit breaker) box through flexible armored or

nonmetallic sheathed copper cable. It is recommended that a

separate circuit serving only this hood be provided.

Wire sizes (copper wire only) and connections must conform

with the rating of the appliance as specified on the model/

serial rating plate. The model/serial plate is located behind

the filter on the rear wall of the hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

A ¹⁄₂" (12.7 mm) UL listed or CSA approved strain relief must

be provided at each end of the power supply cable (at the

range hood and at the junction box).

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling the range hood. Cover

that surface with a protective covering.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto protective

surface.

5. Determine and mark the centerline on the wall where the

hood will be installed.

6. Select a mounting height above the cooking surface to the

bottom of the hood which is between a minimum of

30" (76.2 cm) and a suggested maximum of 36" (91.4 cm).

Mark a reference line on the wall.

NOTE: For installation locations with reduced ceiling heights,

the hood may be installed using the lower vent cover for both

vented and non-vented (recirculating) installations.