Whirlpool 30" (76.2 cm) Cooktop 매뉴얼 - 페이지 7

{카테고리_이름} Whirlpool 30" (76.2 cm) Cooktop에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool 30" (76.2 cm) Cooktop 28 페이지. 30" (76.2 cm) wall-mount canopy range hood
Whirlpool 30" (76.2 cm) Cooktop에 대해서도 마찬가지입니다: 설치 및 사용 설명서 (24 페이지), 사용 및 관리 매뉴얼 (16 페이지)

페이지 인쇄

7. Tape template in place, aligning the template centerline and

bottom of template with hood bottom line and with the

centerline marked on the wall.

A. Centerline

B. Upper screw locations

8. Mark centers of the 4 screw locations through the template to

the wall.

IMPORTANT: All of the screws must be installed into wood.

Remove the template.

9. Drill ⁷⁄₆₄" (2.75 mm) pilot holes at all locations where screws

are being installed into wood.

10. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the hood. See

"Venting Requirements" section.

11. Determine the required height for the ½" conduit and drill a

1¼" (3.2 cm) hole at this location.

12. Run the ½" conduit through the hole. Run wire through the

½"conduit according to the National Electrical Code or CSA

Standards and local codes and ordinances. There must be

enough ½" conduit and wires from the fused disconnect (or

circuit breaker) box to make the connection in the hood's

electrical terminal box.

13. Use caulk to seal all openings.

NOTE: Do not reconnect power until installation is complete.

14. Insert 2 - 5 x 35 mm screws at the upper screw locations, but

do not completely tighten them. Leave a clearance from the

wall of about ½" ( 1.3 cm) for hanging the hood.

A. 5 x 35 mm mounting screws

B. Centerline on wall

Vent Cover Bracket Installation

Installations using telescoping upper and lower vent cover

assembly:

1. Position vent cover bracket on wall about ¹⁄₈" (3 mm) away

from the ceiling.

2. Mark the hole locations.

C. Lower screw locations

D. Mounting height reference

3. Drill ³⁄₈" (9.5 mm) holes for wall anchors and insert anchors

flush with the wall.

4. Attach vent cover bracket to wall using 2 - 10 x 60 mm

drywall anchors and 2 - 6 x 70 mm screws.

A. Centerline on wall

B. 10 x 60 mm drywall anchors

C. Vent cover bracket

D. 6 x 70 mm screws

Install Range Hood

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

1. Tip range hood back and remove metal filters.

2. Using 2 or more people, hang range hood on the 2 previously

installed mounting screws through the keyholes in the back of

the range hood.

3. Level the range hood using a level across the bottom of the

hood.

A. Mounting screws in upper screw locations

B. Keyhole

C. Mounting screws in lower screw locations

D. Centerline on wall

4. Secure range hood with 2 mounting screws (C) through

remaining 2 holes in the hood and into the lower screw

locations.