Whirlpool Ventilation Hood 설치 및 사용 설명서 - 페이지 6

{카테고리_이름} Whirlpool Ventilation Hood에 대한 설치 및 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool Ventilation Hood 32 페이지. Island canopy range hood
Whirlpool Ventilation Hood에 대해서도 마찬가지입니다: 사용 설명서 (7 페이지)

페이지 인쇄

Electrical Requirements

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

IMPORTANT: The hood must be electrically grounded in

accordance with local codes and ordinances, or in the absence of

local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition, or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

Because of the size and weight of this island hood, the chimney

support must be securely attached to the ceiling.

For plaster or drywall ceilings, the chimney support must be

attached to joists. If this is not possible, you must build a

support structure behind the plaster or drywall. The support

structure must be able to support 80 lbs (36.3 kg).

Do not cut a joist or stud unless absolutely necessary. If a

joist or stud must be cut, then a supporting frame must be

constructed.

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

We recommend the hood be installed 30"–36" (76.2 cm –

91.4 cm) above the countertop.

Check your ceiling height and the hood height maximum

before you select your hood.

Hood Height Calculations

1. Select a hood preference height (P) that is comfortable for the

user. 30"– 36" (76.2 cm – 91.4 cm) is recommended.

2. Calculate the hood height for your installation (H = K – C – P ).

3. Confirm that the dimension (H) is within the minimum to

maximum dimensions. See "Product Dimensions" in the

"Location Requirements" section.

4. Calculate the chimney structure height (S = H–1 " [4.4 cm]).

INSTALLATION INSTRUCTIONS

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical circuit is

required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this hood be provided.

Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure range

hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

The range hood must be connected with copper wire only.

The range hood should be connected directly to the fused

disconnect (or circuit breaker) box through flexible armored

cable or flexible metallic conduit.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70, latest edition, or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91, latest edition, and all local codes and

ordinances.

1 "

(4.4 cm)

K = ceiling height

C = countertop height

P = preferred hood height –

30"–36" (76.2 cm – 91.4 cm)

is recommended

H = K – C – P

ceiling to bottom of hood

S = H –1 " (4.4 cm)

chimney assembly height