Xerox Phaser 6180 시작하기 - 페이지 12

{카테고리_이름} Xerox Phaser 6180에 대한 시작하기을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox Phaser 6180 28 페이지. Color laser printer
Xerox Phaser 6180에 대해서도 마찬가지입니다: 사용자 설명서 (1 페이지), 보충 설명서 (3 페이지), 빠른 사용 설명서 (5 페이지), 설치 매뉴얼 (1 페이지), 보충 설명서 (1 페이지), 지침서 (2 페이지), 지침서 (2 페이지), 지침서 (2 페이지), 지침서 (2 페이지), 지침서 (1 페이지), 지침서 (1 페이지), 지침서 (1 페이지), 지침서 (1 페이지), 평가자 매뉴얼 (16 페이지), 사양 (4 페이지), 서비스 매뉴얼 (17 페이지), 설치 매뉴얼 (2 페이지), 빠른 사용 설명서 (6 페이지), (포르투갈어) 빠른 시작 가이드 (5 페이지)

페이지 인쇄
Xerox Phaser 6180 시작하기
DOCUSP 3.6.xx
2-2
Caveat
When a copy sensitive FORM command
causes a change to the back side, side 2, of a
page, the form does not print on side 2 but
prints on side 1 of the next page.
A DJDE syntax error is raised when a DJDE
command RTEXT=(TEST) is used, where
TEST is the name of a TST file.
If an LCDS job is submitted after a DocuSP
restart, a fault clearance message may
appear. Clear the fault and the system prints
correctly.
A large number (e.g. 100+) of jobs submitted
with the printer paused causes the printer to
cycle down intermittently after the printer
resumes printing. Single page printing
performance is very slow. Do not submit a
large number of single page jobs while the
printer is paused.
After changing the output order or output
delivery of a printing job, and then selecting
Apply Properties Now, the system hangs.
Restart the system, then delete and resend
the job.
Do not attempt to program a paper tray that
contains ordered stock and is currently being
used by a printing job.
After a restart of the DocuSP software, the
Queue Manager, Printer Manager,
Administration, Job Manager, and Reprint
Manager windows may take up to 5 minutes to
come up. As a workaround, exit power saver
mode before restarting the system, or power
on power off the printer during the restart.
Any job with a paper size US Legal or US
Letter short edge feed and single portrait
stitching becomes ineligible with the message
"Job was received with a programming
conflict. Finishing is not available for jobs with
this media orientation."
The system may display an unclearable Reset
message. The system prints normally.
When Offset stacking is enabled, stitched jobs
do not offset.
Applicable printer product
DocuTech/DocuPrint 75/90
DocuPrint 1xx EPS
DocuTech/DocuPrint 75/90
DocuPrint 1xx EPS
DocuTech/DocuPrint 75/90
DocuPrint 1xx EPS
DocuTech/DocuPrint 90
DocuTech/DocuPrint 75/90
DocuTech/DocuPrint 75/90
DocuTech/DocuPrint 75/90
DocuTech/DocuPrint 75/90
DocuTech/DocuPrint 75/90
DocuTech 61xx
XEROX DOCUMENT SERVICES PLATFORM SERIES
GETTING STARTED