Xerox Nuvera 100 사용자 설명서 - 페이지 9

{카테고리_이름} Xerox Nuvera 100에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox Nuvera 100 40 페이지. Production system
Xerox Nuvera 100에 대해서도 마찬가지입니다: 사양 시트 (2 페이지), 기능 설명서 (34 페이지), 계획 매뉴얼 (22 페이지), 운영 매뉴얼 (34 페이지), 참조 매뉴얼 (2 페이지), 계획 매뉴얼 (20 페이지), 참조 매뉴얼 (42 페이지), 빠른 참조 (2 페이지), 설치 매뉴얼 (2 페이지), 보충 설명서 (48 페이지), 계획 매뉴얼 (38 페이지), 계획 매뉴얼 (16 페이지), 참조 매뉴얼 (2 페이지), 사양 (2 페이지), 힌트 및 팁 매뉴얼 (18 페이지), 힌트 및 팁 매뉴얼 (18 페이지), 시작하기 매뉴얼 (26 페이지), 시작하기 매뉴얼 (30 페이지)

Media for the MICR fonts

MICR User Guide

MICR Fonts CD-ROM

The PostScript, PCL, and LCDS MICR fonts are provided

on two CD-ROMs—one for 300 dpi printing and one for

600 dpi and above. The two CDs contain the same fonts

except for the following:

The 600 dpi MICR Fonts CD contains the E13B9 and

E13B PostScript 600 dpi fonts.

The 300 dpi CD contains a 300 dpi version of the

E13B PostScript font. It does not contain E13B9,

which is 600 dpi only.

Note: When loading your fonts from CD, load the fonts

from either the 600 dpi MICR Fonts CD or the 300 dpi

CD. If both versions of the 9.12 point E13B PostScript

font are present on the system at the same time,

unpredictable results can occur. For this reason, two CDs

are provided, each containing a different version of the

9.12 point E13B PostScript font.

If you have loaded your MICR fonts from the 600 dpi CD

and you want to print using the 300 dpi PostScript MICR

font, you must first delete the 600 dpi E13B.PFB font, then

reload the 300 dpi E13B.PS font from the 300 dpi CD.

If fonts were loaded from the 300 dpi CD, delete the 300

dpi E13B.PS font before loading the 600 dpi E13B.PFB

font. (Refer to "Installing PostScript and PCL fonts," later

in this chapter, for the font loading procedure.)

Media for IPDS fonts

AFP MICR fonts, supporting the IPDS datastream, are

provided at 300 dpi on various media (CD, cartridge tape,

or diskette). Follow instructions for your host system for

loading these fonts on the host.

To install the PostScript and PCL fonts, follow these

steps.

1. Log in at the Administrator level.

2. Insert the "DocuPrint MICR Fonts" CD into the CD-

ROM drive.

3. Click the Administration icon on the main DocuSP

window.

MICR fonts

2-3