Xerox WORKCENTRE C2424 사용자 설명서 - 페이지 5

{카테고리_이름} Xerox WORKCENTRE C2424에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox WORKCENTRE C2424 43 페이지. Copier-printer
Xerox WORKCENTRE C2424에 대해서도 마찬가지입니다: 빠른 참조 매뉴얼 (14 페이지), 브로셔 (8 페이지), 보충 설명서 (7 페이지), 사양 (6 페이지), 시작하기 매뉴얼 (26 페이지), 사용자 설명서 (21 페이지), 사용자 설명서 (20 페이지), 유지 관리 매뉴얼 (20 페이지), 사용자 설명서 (19 페이지), 사용 설명서 (16 페이지), 매뉴얼 (12 페이지), 사용 설명서 (6 페이지), 설치 매뉴얼 (4 페이지), 설치 매뉴얼 (2 페이지), 피드 롤러 키트 교체 (2 페이지), 설정 매뉴얼 (2 페이지), 자발적 제품 접근성 템플릿 (10 페이지), 경쟁사 비교 (3 페이지), 빠른 참조 매뉴얼 (14 페이지), 서비스 매뉴얼 (11 페이지), 빠른 참조 매뉴얼 (13 페이지)

Configuring the Network Address

TCP/IP and IP Addresses

If your computer is on a large network, contact your network administrator for the appropriate

TCP/IP addresses and additional configuration information.

If you are creating your own small Local Area Network or connecting the system directly to

your computer using Ethernet, follow the procedure for automatically setting the system's

Internet Protocol (IP) address.

PCs and systems primarily use TCP/IP protocols to communicate over an Ethernet network.

With TCP/IP protocols, each system and computer must have a unique IP address. It is

important that the addresses are similar, but not the same; only the last digit needs to be

different. For example, your system can have the address 192.168.1.2 while your computer has

the address 192.168.1.3. Another device can have the address 192.168.1.4.

Generally, Macintosh computers use the EtherTalk protocol to talk to a networked system.

Unlike TCP/IP, EtherTalk does not require systems or computers to have IP addresses.

Many networks have a Dynamic Host Configuration Protocol (DHCP) server. A DHCP server

automatically programs an IP address into every PC and system on the network that is

configured to use DHCP. A DHCP server is built into most cable and DSL routers. If you use a

cable or DSL router, see your router's documentation for information on IP addressing.

For more information, go to the table of

this section.

Automatically Setting the System's IP Address

If the system is connected to a small established TCP/IP network without a DHCP server, use

the Installer on the WorkCentre C2424 Software CD-ROM to detect or assign an IP address to

the system. For further instructions, insert the software CD-ROM into your computer's CD-

ROM drive. After the Installer launches, follow the prompts for installation.

Note

For the automatic Installer to function, the system must be connected to an established

TCP/IP network.

Connections and Internet Protocol (TCP/IP)

infoSMART Knowledge Base documents

WorkCentre® C2424 Copier-Printer

6-5

at the end of