Xerox Phaser 6100DN 설치 및 운영 매뉴얼 - 페이지 2

{카테고리_이름} Xerox Phaser 6100DN에 대한 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox Phaser 6100DN 8 페이지. Disk overwrite installation and usage
Xerox Phaser 6100DN에 대해서도 마찬가지입니다: 설치 매뉴얼 (34 페이지), 사양 (2 페이지), 사용자 설명서 (32 페이지), 브로셔 및 사양 (4 페이지), 사용자 설명서 (28 페이지), 설치 매뉴얼 (2 페이지), 보안 매뉴얼 (38 페이지), 설치 매뉴얼 (2 페이지), 릴리스 노트 (2 페이지), 시작하기 매뉴얼 (37 페이지), 매뉴얼 (34 페이지), 매뉴얼 (34 페이지), 시작하기 매뉴얼 (34 페이지), 사용자 설명서 (32 페이지)

Xerox Phaser 6100DN 설치 및 운영 매뉴얼
Pre-installation procedures
Before the Disk Overwrite software can be installed, the following must be completed:
1. If a scrape is required, back up all saved jobs, fonts, forms, resources, and customer-installed software. This is
the responsibility of the customer.
2. If DocuSP 3.8 is installed on the system, the Xerox Service Representative installs the Solaris Operating System
version 8 for Disk Overwrite. This installation requires a scrape and repartition of the hard disk(s).
If the system is running a version of DocuSP later than 3.8, a scrape is necessary ONLY if the system has not
been scraped since the upgrade to DocuSP 4.X or higher. Use the Solaris Operating System version delivered
with the DocuSP software to perform the scrape.
If the system is running DocuSP 4.2 on a Sun W1100Z controller, the DocuSP Disk Overwrite 4.2 Self Install
Patch is required. The patch should be installed prior to the Disk Overwrite software installation. Refer to the
patch installation instructions provided with the Patch CD.
If the system is running DocuSP 50 or higher, two options are presented during the operating system installation:
Data Overwrite is planned to be used on this system
Backup is planned to be used on this system
Both options must be checked in order to run the Disk Overwrite software. If these two options were not checked,
a scrape install of the system is required and the two options checked.
NOTE: If the Disk Overwrite software is reinstalled for any reason, for example to change the partitioning, it is not
necessary to reinstall the Solaris Operating System.
Installing the Disk Overwrite software
To install the Disk Overwrite software:
1. Insert the Disk Overwrite CD into the CD/DVD ROM drive.
2. A window opens and a log-in prompt displays.
3. Enter the root password and press <Enter>.
NOTE: For certain security settings on DocuSP, automatically installing software on a CD may be prohibited. If
the Disk Overwrite CD is inserted into a CDROM or DVDROM drive and a window does not open after the CD
has been detected, manually install the software by opening a terminal window, logging in as root, and entering
the following command to start the installation process:
WARNING: Do not run any other programs on the CD to load the software. An improper installation could
result in unknown side effects and cause the system to be unstable.
701P45144
June 2006
2
/cdrom/cdrom0/volstart