Yamaha YDP-101 소유자 매뉴얼 - 페이지 23

{카테고리_이름} Yamaha YDP-101에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha YDP-101 48 페이지. Yamaha digital piano owner's manual
Yamaha YDP-101에 대해서도 마찬가지입니다: (영어) 사용 설명서 (47 페이지)

Yamaha YDP-101 소유자 매뉴얼
START /
TRACK
STOP
REC
1
2
START /
TRACK
STOP
REC
1
2

Playback

To play back what you've recorded, first make sure that the green track
indicators of the tracks you want to play are lit. If not, press the corresponding
track button(s) so that they are lit. Then press the [START/STOP] button.
Playback starts from the beginning of the recorded data, and will stop automati-
cally at the end of the recorded data. You can also stop playback at any time by
pressing the [START/STOP] button.
To mute a track so that it doesn't play back, press the corresponding track
button so that its indicator goes out (press again to turn the track back on).
The current measure number appears on the display during playback.
• It is possible to play along on the keyboard during playback. In this case, the
playback voice and the voice you play on the keyboard are not the same. The
playback voice is the voice that was set when the data was recorded. The voice you
play on the keyboard is the voice that is selected on the panel.
• The playback volume and tempo can be adjusted by using the [MASTER VOLUME]
control and [TEMPO M / L ] buttons (press both [TEMPO M / L ] buttons simulta-
neously to recall the default tempo).
• All recorder data will be retained in memory for about one week after the power is
turned off. If you want to keep your recorded data for longer periods, turn the power
on for a few minutes at least once a week. It is also possible to store it to an
external MIDI storage device by using the Bulk Data Dump function described on
page 30.
• The track indicators will not light automatically when the power is turned on even if
the recorder contains data. It is therefore necessary to press the track buttons so
that the corresponding green indicators light before starting recorder playback. It is
also a good idea to press the track buttons to check if the tracks contain data
before recording. If the green indicator lights when the corresponding track button
is pressed, that track contains data which will be erased and replaced by the newly-
recorded data.
• If the metronome is being used during playback, the metronome will automatically
stop when playback is stopped.
• During recorder playback, the volume of a track which is turned off will always be
"0" (i.e. the "Piano Song Part Cancel Volume" function — page 27 — only affects
piano song playback.
• The playback data is not transmitted via the MIDI OUT connector.
• Playback cannot be started when the demo/piano song mode is engaged.
• Playback cannot be started when the recorder contains no data, or when both track
buttons are off.
• When using REVERB during playback, depending upon the conditions one reverb
type will take priority.

Synchro Start

....................................................................................................................
When the Synchro Start function is engaged, recorder playback will begin
automatically as soon as you start playing on the keyboard.
To engage the Synchro Start function press the [START/STOP] button
while holding a track button which is ON. The rightmost dot on the display will
flash at the current tempo. (Repeat the previous operation to disengage the
Syncro Start function.) Playback will then start as soon as you begin playing on
the keyboard.
If you hold a track button which is OFF while pressing the [START/STOP]
button, that track will be turned ON and the Synchro Start mode will be engaged.

Left Pedal Start/Stop

The left pedal can be assigned to start and stop recorder playback via the
"Left Pedal Mode" function described on page 27. This is convenient for start-
ing playback of the recorded part anytime after you have started playing.
Using the Recorder
.................................................................................................
23
YDP-101