Yamaha AG-Stomp 소유자 매뉴얼 - 페이지 9

{카테고리_이름} Yamaha AG-Stomp에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha AG-Stomp 32 페이지. Yamaha accoustic guitar/pre-amplifier owner's manual
Yamaha AG-Stomp에 대해서도 마찬가지입니다: 서비스 매뉴얼 (45 페이지), 패치 목록 (1 페이지), (네덜란드어) 매뉴얼 (32 페이지)

페이지 인쇄

I Rear Panel

@6 Power Switch (STAND-BY ON/OFF)

This is the unit's power switch.

* To protect the speakers, always set the OUTPUT knob

to "0" before switching the power ON/OFF.

@7 Power Adaptor Jack (AC IN 12V 1A)

Connect the supplied power adaptor to this jack.

* Never use a power adaptor other than the supplied adaptor.

Use of any other adaptor may result in damage, overheating,

fire, etc.

@8 Guitar Power Supply Switch

(+9V SUPPLY ON/OFF)

This switch allows the delivery of power (DC9V) to

an electric-acoustic guitar's built-in pre-amplifier

through the AG-Stomp's INPUT jack via the sup-

plied TRS phone cable. (→ page 12)

@9 MIDI OUT Jack

This jack is used to transmit MIDI data from the AG-

Stomp such as control changes, program changes,

data in the AG-Stomp's memory, etc. (→ page 18)

#0 MIDI IN Jack

This jack is used to receive MIDI data from an ex-

ternal MIDI device such as a MIDI Foot Controller,

etc., which can be used select patches, control vol-

ume or control the AG-Stomp's individual effects.

(→ page 18)

Also, AG-Stomp data saved in an external MIDI de-

vice can be returned to the AG-stomp via this jack.

(→ page 25)

#1 Digital Output Jack (DIGITAL OUT)

This jack is used to transmit the output of the AG-

Stomp as digital data. Connect this jack to the digi-

tal input jack (COAXIAL) of a digital mixer, etc. (→

page 11)

#2 EXP. PEDAL Jack

Connect a foot controller (expression pedal) (op-

tional) such as the YAMAHA FC-7 to this jack and

control individual parameter's of the AG-Stomp. (→

page 22, 26)

#3 Headphone Jack (PHONES)

Connect a pair of headphones (optional) to this jack

to monitor the AG-Stomp's sound when you want to

practice privately. (→ page 11)

* Even when headphones are connected to this jack, the

audio signal is delivered from the OUTPUT Jack

the DIGITAL OUT Jack

#4 Output Jacks (OUTPUT R, L/MONO)

These are the AG-Stomp's analog output jacks (TRS

balanced). Connect these jacks to the input jacks

on a power amp and speaker system, guitar ampli-

fier, mixer, etc.

A commercially available PA type TRS phone cable

can be used to send a TRS balanced audio signal

from the AG-Stomp. Also, the supplied TRS-XLR

converter cables connected to these jacks deliver a

balanced audio signal to the XLR jacks on a mixer,

etc. (→ page 10)

* Use the L/MONO jack when connecting to a monaural de-

vice.

#5 INPUT Jack

#6 Input MUTE Switch

This is the AG-Stomp's input jack. Connect a guitar

to this jack.

The supplied TRS phone cable can be used to de-

liver power to an electric-acoustic guitar's built-in pre-

amplifier from the AG-Stomp. (→ page 12)

When pressed, the Input MUTE Switch (

the signal from the INPUT jack to prevent noise,

etc. from entering the circuit. Use this switch when

connecting or disconnecting the guitar's cable.

Nomenclature

and

) cuts