Yamaha AX-497 서비스 매뉴얼 - 페이지 2
{카테고리_이름} Yamaha AX-497에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha AX-497 36 페이지. Stereo amplifier
Yamaha AX-497에 대해서도 마찬가지입니다: 소유자 매뉴얼 (23 페이지), 소유자 매뉴얼 (24 페이지)
페이지 인쇄
- 1. Table of Contents
- 2. Important Notice
- 3. To Service Personnel
- 4. Impedance Selector
- 5. Remote Control Panel
- 6. Front Panel
- 7. Rear Panels
- 8. Specifications
- 9. Internal View
- 10. Disassembly Procedures
- 11. Adjustment
- 12. IC Data / Block Diagram
- 13. Pin Connection Diagram / Printed Circuit Board
- 14. Parts List
- 15. Exploded View
- 16. Remote Control Rax15
AX-497
QQ
3 7 63 1515 0
TO SERVICE PERSONNEL
1. Critical Components Information
Components having special characteristics are marked Z
and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.
Meter impedance should be equivalent to 1500 ohms shunted
by 0.15µF.
"CAUTION"
"F151, F152 : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 8A, 125V FUSE."
A
V
CAUTION
F151, F152 : REPLACE WITH SAME TYPE 8A, 125V FUSE.
ATTENTION
F151, F152 : UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 8A, 125V.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or
plastic (where applicable) components may also contain traces of chemicals found by the California Health and
Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR
TE
ANY REASON WHATSOEVER!
L 13942296513
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes
or expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands
before handling food.
About Lead Free Solder /
The P.C.B.s installed in this unit are soldered using the fol-
lowing solder.
www
Among some types of lead free solder currently available, it
is recommended to use one of the following types for the
repair work.
.
• Sn + Ag + Cu (tin + silver + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)
2
http://www.xiaoyu163.com
SMT
Side A
Solder Dip
Side B
MI
x
ao
u163
y
i
http://www.xiaoyu163.com
2 9
8
EQUIPMENT
WALL
OUTLET
UNDER TEST
INSULATING
TABLE
Leakage current must not exceed 0.5mA.
Be sure to test for leakage with the AC plug in both
polarities.
Q Q
3
6 7
1 3
1 5
REFLOW
Process
FLOW
Process
co
.
9 4
2 8
AC LEAKAGE
TESTER OR
EQUIVALENT
0 5
8
2 9
9 4
2 8
m
9 9
9 9