Yamaha TX4n 소유자 매뉴얼 - 페이지 7

{카테고리_이름} Yamaha TX4n에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha TX4n 24 페이지. Txn series
Yamaha TX4n에 대해서도 마찬가지입니다: 사양 (4 페이지), 소유자 매뉴얼 (24 페이지), 소유자 매뉴얼 (24 페이지), 소유자 매뉴얼 (24 페이지), 소유자 매뉴얼 (24 페이지)

페이지 인쇄

Thank you for purchasing the Yamaha TX6n, TX5n, TX4n Power Ampliﬁer. In order

to take full advantage of the TX6n/TX5n/TX4n's (TXn) functionality and to ensure

trouble-free operation, please read this owner's manual carefully before use. After you

have read the manual, keep it in a safe place for reference when needed.

Features

The TXn series are high audio quality, high efﬁciency, high reliability, low impedance drive power ampliﬁers that

utilize Yamaha's famed DSP and digital audio networking technology.

■ Flexible support for analog and digital audio formats

In addition to two-channel analog input, these ampliﬁers come with an AES/EBU card installed in their MY card slot,

allowing digital signals to be input and output. Separately sold MY cards can be installed in this MY slot to support a vari-

ety of digital audio formats.

■ Monitor and control from Amp Editor

By connecting a computer in which the "Amp Editor" application software is installed, the computer can be used to monitor

the TXn units, or to control the TXn units such as switching the ampliﬁer power's Standby/On and mute status. This moni-

toring and control can also be performed from the panel of the TXn unit.

■ Versatile speaker processing

Since signal processors such as equalizer, delay, and crossover are built in, the use of external equipment can be minimized.

These can be controlled from the panel of the TXn unit or via Amp Editor. Speaker processor libraries created on the

Yamaha DME series or the SP2060 can also be used.

About Setup

■ Attaching the handles

You can attach the handles to the ampliﬁer using the supplied ﬂat-head screws.

Follow the steps below to attach the handles:

1. Remove the rack mount brackets.

2. Attach the handles to the ampliﬁer by tightening the ﬂat-head screws into the four screw holes for each handle.

3. Replace the rack mount brackets.

■ Adjusting the position in the rack

If there is insufﬁcient space between the rear of the ampliﬁer and the rack, you can adjust the position of the rack mount

brackets so that the front panel of the ampliﬁer protrudes from the front of the rack by 22 mm.

Related manuals and software

This manual primarily explains how to set up the TXn at the time of installation. Manuals that contain detailed

explanations of the TXn and Amp Editor, as well as Amp Editor itself, can be downloaded from the following website.

http://www.yamahaproaudio.com/

• List of related manuals

TX6n/5n/4n Reference Manual

Amp Editor Installation Guide

Amp Editor Owner's Manual

• In order to view the downloaded manuals, Adobe Reader must be installed in your computer. If you don't have Adobe

NOTE

Reader, please access the Adobe Corporation's website at the following URL, and download Adobe Reader (free of

charge).

http://www.adobe.com/

Introduction

Provides a detailed explanation of the TXn's panel operations, etc.

Explains the installation and uninstallation procedures for Amp Editor.

Explains how to use Amp Editor.

TX6n/5n/4n Owner's Manual