Yamaha HS8I 소유자 매뉴얼 - 페이지 7

{카테고리_이름} Yamaha HS8I에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha HS8I 20 페이지. Powered studio monitor and powered subwoofer
Yamaha HS8I에 대해서도 마찬가지입니다: 소유자 매뉴얼 (20 페이지), 소유자 매뉴얼 (20 페이지), 소유자 매뉴얼 (20 페이지), 소유자 매뉴얼 (20 페이지), 소유자 매뉴얼 (20 페이지)

Yamaha HS8I 소유자 매뉴얼
HS8S (Subwoofer)
1

Subwoofer Connections

1 INPUT L/R connector
These connectors receive the input signal to the
subwoofer. Balanced XLR and balanced phone jack
connectors are provided for both the L and R inputs.
The L and R inputs can be used simultaneously.
Signals supplied to both the L and R inputs are mixed
internally.
NOTE The XLR and phone jack input connectors can not be
used simultaneously. Use only one input connector at a
time.
NOTE Refer to "Connectable cables" on page 5 for more
connector details.
Connectin the Subwoofer to the
HS8/HS7/HS5 Speakers
2 OUTPUT L/R connectors
These are the subwoofer's output connectors.
The input signals received at the INPUT L and R
connectors are output via the OUTPUT L and R
connectors, respectively. Low frequency reproduction
characteristics can be adjusted via the LOW CUT
switch and LOW CUT control.
3 LOW CUT switch
When this switch is ON, the low frequencies are
attenuated prior to output via the OUTPUT L and R
connectors at the frequency set by the LOW CUT
control. The low-frequency attenuation cutoff
frequency can be adjusted via the LOW CUT control.
4 LOW CUT control
Adjusts the low-frequency attenuation cutoff
frequency between 80 Hz and 120 Hz when the LOW
CUT switch is ON.
3
2
4 5
7
HS8S
si nal flow
Subwoofer Response Control
5 HIGH CUT control
Sets the cutoff frequency for subwoofer output high-
frequency attenuation from 80 Hz to 120 Hz.
6 PHASE switch
Switches the phase of the subwoofer output.
This switch should be set to [NORM.] in most
situations, but in combination with some speakers
and in some speaker layouts switching to the [REV.]
setting may improve low-frequency response. Select
the setting that provides the best bass response in
your system.
7 LEVEL control
Adjusts the subwoofer output level.
8 Power switch
Turns power to the subwoofer ON or OFF.
Rock the switch to the right [
the left [
panel will light when the power is ON.
NOTICE
• Turning the power switch ON and OFF in rapid succession can cause
the device's electronics to malfunction. Please wait for 3 seconds or
more after turning the power OFF before turning it ON again.
• Even when the power switch is turned off, electricity is still flowing to
the product at the minimum level. When you are not using the product
for a long time, make sure to unplug the power cord from the wall AC
outlet.
9 AC IN connector
Connect the supplied power cable here. First connect the
power cord to the subwoofer, then insert the power cord
plug into the AC outlet.
6
1
34
5
] to turn the power ON, or to
] to turn the power OFF. The logo on the front
HS8/HS7/HS5/HS8I/HS7I/HS5I/HS8S Owner's Manual
8
9
2
6 7
7