Clark Synthesis TST239 설치 매뉴얼 - 페이지 10

{카테고리_이름} Clark Synthesis TST239에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Clark Synthesis TST239 20 페이지. Platinum, gold, silver and all weather transducers
Clark Synthesis TST239에 대해서도 마찬가지입니다: 보충 설명서 (4 페이지), 설치 매뉴얼 (8 페이지), 데이터시트 (1 페이지), 구매자 매뉴얼 (2 페이지), 설치 매뉴얼 (20 페이지), 사양 (1 페이지)

페이지 인쇄

Installation: Laminated I-Beam Floors

Laminated I-Beam Joists

INSTALLATION USING THE UNIMOUNT BRACKET

1. Attach a 1" by 6" hardwood bridge to the two I-beams using adhesive and screws.

2. Attach the unimount bracket to the bridge using machine screws with flat washers and

lock washers.

3. Screw the a threaded stud into the threaded insert on the unimount bracket.

4. Spin the two jam nuts onto the stud. You will tighten them later.

5. Screw the Transducer onto the stud until a slight resistance is felt (approx. 5 or 6 turns).

When resistance is felt, stop turning. DO NOT OVERTIGHTEN THE Transducer!

6. Tighten one jam nut against the unimount bracket.

7. Tighten the other jam nut against the Transducer's brass nut using two 9/16" wrenches as follows: One

wrench firmly grasping the Transducer's brass nut while the second tightens the jam nut against it.

NEVER TIGHTEN BY TURNING THE Transducer – MAKE SURE TO TIGHTEN THE JAM NUT AGAINST THE

Transducer'S BRASS NUT.

8. Use solder or wire nuts to connect speaker wire to the Transducer's wire leads.

9. Run the speaker wire to your audio system.

10. Connect the Transducer to your audio system (see "Amplifiers & Wiring" in this guide).

INSTALLATION USING THE T-NUT

1. Drill a 7/16" hole in a 1" by 6" hardwood bridge. Press the T-nut into the hole on the

side of the mounting surface opposite the Transducer.

1. Attach the hardwood bridge to the two I-beams using adhesive and screws.

2. Screw a threaded stud completely into the T-nut.

3. Place the 3/8" flat washer and 3/8" lock washer on the threaded stud, then spin the two

jam nuts onto the stud (flat washer against the mounting surface, lock washer between

flat washer and jam nut). You will tighten the jam nuts later.

4. Screw the Transducer onto the stud until slight resistance is felt (approx. 5 or 6 turns).

When resistance is felt, stop turning. DO NOT OVERTIGHTEN THE Transducer!

5. Tighten one jam nut against the lock washer, flat washer, and mounting surface.

6. Follow steps 6 through 9 under "INSTALLATION USING THE UNIMOUNT BRACKET" (as

shown above).

Tactile Sound Transducers

The Transducer mounts on 1"x 6" hardwood bridge spanning two joists,

using the unimount bracket (shown) or the threaded stud with T-nut. Attach

the bridge to the bottom face of the joists using adhesive and screws.

MOUNTING DETAIL

Washers

Screws

Jam Nuts

MOUNTING DETAIL

T-Nut

Washers

Jam Nuts