Directed Xpresskit DBALL2 설치 매뉴얼 - 페이지 5

{카테고리_이름} Directed Xpresskit DBALL2에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed Xpresskit DBALL2 18 페이지. Ford5 remote start ready (rsr) installation
Directed Xpresskit DBALL2에 대해서도 마찬가지입니다: 설치 매뉴얼 (12 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (18 페이지), 매뉴얼 (14 페이지), 설치 매뉴얼 (13 페이지), 설치 매뉴얼 (14 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (15 페이지), 설치 및 빠른 참조 매뉴얼 (16 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (16 페이지), 매뉴얼 (19 페이지), 설치 매뉴얼 (11 페이지), 설치 매뉴얼 (10 페이지)

페이지 인쇄
Directed Xpresskit DBALL2 설치 매뉴얼
Platform: DBALL2
Firmware:
HYUNDAI9 Remote Start Ready (RSR) Installation
Installation Type 2
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
87
86
87a
30
Fuse
30A
Smart Key Ign. Interrupt (conn. side): Orange/Red: 10
Smart Key Ign. Interrupt (veh.side): Yellow/Red: 11
31
1
(+) 12V:
White,
32
22
12
2
pin 31
33
23
3
13
34
24
14
4
35
25
15
5
36
26
21
16
6
37
27
17
7
38
28
18
8
39
29
19
9
40
30
20
10
I/P-A Fusebox/Smart Junction Box
41 11
(White conn. front of
fusebox/smart junction box)
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
(+) Starter:
Red/Black,
86
87
85
87a
30
(+) Ignition:
Blue, pin 41
85
C-CAN High: Green, pin 6
C-CAN Low: Orange, pin 14
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) 12V: Red: 13
(-) Ground: Black: 14
(-) Ignition Output: Black/White: 1
(+) Accessory Output: Gray: 6
(+) Starter Output: Gray/Black: 7
(MUX) Parking Lights Output: Violet/Brown: 9
EMS COM: Orange/Black: 11
(MUX) Parking Lights:
Yellow, pin 14
1
2
3
4
5
6
7
8
Headlight/Wiper switch
9
10
11
12
13
14
15
16
(Black conn. at steering column)
1
3
EMS COM: Blue, pin 3
42
1
31
8
32
25
19
9
43
2
33
26
20
10
44
3
34
27
21
11
pin 45
35
12
45
4
36
13
46
5
37
28
22
14
38
29
23
15
47
6
39
16
48
7
40
17
41
30
24
18
(+) Accessory:
Green, pin 30
Green/Black, pin 3
Diagnostic Connector
1
8
OBDII (connector side view)
9
16
RF
DBALL2
Prog. Button
LED
MC11 Junction
(Blue conn. at
driver kick panel)
Smart Key Ignition Interrupt
Green, pin 6
B-CAN Low:
Blue/Black, pin 4
1
3 4
5
6
7 8
2
13 14 15 16
11 12
B-CAN High:
I/P-F Fusebox/Smart Junction Box
(White conn. rear of
fusebox/Smart Junction Box)
Note: Hood pin only required
on vehicles not equipped
with a factory hood pin.
Hood Pin
Remote Start Safety
Override Switch
6: White/Black,(-) Hood
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
© 2015 Directed. All rights reserved.
Rev.: 20161206
Page 5
Required for
CUT
vehicle takeover
10
9
17
18