Zanussi ZKT 621 LX 작동 및 설치 지침 - 페이지 16
{카테고리_이름} Zanussi ZKT 621 LX에 대한 작동 및 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Zanussi ZKT 621 LX 22 페이지. Elektric ceramic glass hob
Zanussi ZKT 621 LX에 대해서도 마찬가지입니다: 설치 및 운영 지침 매뉴얼 (18 페이지)
페이지 인쇄
What to do ...
If the hob does not function correctly, please carry out
the following checks, as it may be something you can
remedy yourself.
...
if the cooking zones will not function?
Check, whether
the main fuse has failed.
D
the appliance is correctly switched on.
D
the safety cut off has operated.
D
the control lamps of the control panel are lighting.
D
the corresponding cooking zone is switched on.
D
the cooking zones are set for cooking as desired.
D
...
if cooking zones cannot be switched on/off?
Check, whether
the control panel is locked.
D
a period of more than 10 seconds has elapsed
D
between pressing the on/off switch and selecting
a cooking zone.
the touch controls are entirely or partly covered by
D
liquid or by a wet cloth.
...
if the whole indicator section for residual heat,
except
, will fail all of a sudden?
Check, whether
the ON/OFF touch control
D
touched.
the touch controls are entirely or partly covered by
D
liquid or by a wet cloth.
the safety cut off has operated.
D
there was a power cut for a short while.
D
...
if the displays suddenly go out?
Check, whether
the fuse has failed.
D
there has been a power cut.
D
the setting operation was correctly made.
D
...
if after cooking zone switch- -off the display will
not show
or
for residual heat?
Check, whether
the cooking zone has only been in operation for a
D
short while, and is therefore not hot enough.
...
if a cooking zone cannot be switched on?
Check, whether
the child--safety
D
...
if all displays (inclusive of residual heat indica-
tor
) go out during cooking?
was accidentally
is switched on.
The overheating protection of the electronic con-
D
trols has blocked the use of the hob. Once the
cooking zone has cooled down it can be operated
again.
...
if the display
If the hob has been used at a high setting for a
long period of time, the overheating protection of
the electronic control will become active and the
front left cooking zone will become inoperable.
This occurs to prevent damage to the electronic
controls. The front left cooking zone will operate
again once the appliance has cooled down and
is no longer in the display. The front right and rear
cooking zones can still be operated during this
time.
...
if the display
Check, whether
the touch controls are entirely or partly covered or
D
contaminated by liquid or by a wet cloth.
Clean the ceramic glass surface and wipe it dry.
D
If after switching the appliance back on, the dis-
D
play still shows
Force Centre.
If after carrying out the above checks your appliance is
still faulty, disconnect from the mains supply and con-
tact your local Service Force Centre.
In guarantee customers should ensure that the
above checks have been as the engineer will make
a charge if the fault is not a mechanical or electrical
breakdown.
Please note that proof of purchase is required for
any in- -guarantee service calls.
Service and Spare Parts
If you require an engineer or you wish to purchase
spare parts contact your local Service Force Centre by
telephoning:
Your call will be routed to the Service Centre covering
your post code area.
When you contact the Service Centre you will need to
give the following details:
1
Your name, address and post code.
2
Your telephone number.
3
Clear and concise details of the fault.
4
The model and serial numer of the appliance
(Found on the rating plate).
5
The purchase date.
In guarantee customer should ensure that the checks
listed in „What to do" have been made as the engineer
will make a charge if the fault is not a mechanical or
electrical breakdown.
16
flashes?
lights up?
. Contact your local Service
0990- - 929929