Clarke 6470057 조립 지침 - 페이지 2

{카테고리_이름} Clarke 6470057에 대한 조립 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Clarke 6470057 2 페이지. Mitre saw

페이지 인쇄

Thank you for purchasing this CLARKE Mitre Saw, which is designed for DIY, Hobby and

Professional users alike.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of 12 months

from the date of purchase. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in

any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to

us without prior permission.

This guarantee does not effect your statutory rights.

COMPONENT GUIDE

Fig. 1

GROUP C - Pivot Pin, c/w 2 locating

screws (with pointed ends)

GROUP D - Four plastic feet c/w fixing

screws

GROUP E - Two Depth of Cut Stops -

locate on Guide Rods, one

at each end of thre carriage

GROUP F - Four Base fixing screws with

Hex. key

Not Shown - Base and Saw complete

Unpack and lay out all components,

identifying each one according to the

schedule below. Should any part br missing

or damaged, contact your Clarke dealer

immediately.

GROUP A - Length Stop Assembly, compr:

1. Two Rods - one long with threaded end,

one short.

2. Lock nut - screw on to end of long rod.

3. Plastic pad - fits on flat end of short rod.

4. Clamp assy c/w two clamping screws

GROUP B - Work Clamp Assembly, compr:

1. One short rod with threaded end.

2. Lock nut - screw on to end of short rod.

3. Adjuster Screw.

4. Plastic Pad - fits on end of Adjuster Screw.

5. Clamp Assembly complete with clamping

screw

ASSEMBLY

1. Mitre Table to Carriage

Attach the Carriage to the Mitre Table so that the

pointer locates over the ledge, at the side of the Mitre

Table, as shown in fig.2. It will be necessary to lift the

locking lever, to depress the locking mechanism, so

that the two components can be connected.

Line up the pivot hole in the Carriage with that in the

Mitre Table, and slide in the Pivot Pin from below as

shown in fig. 3. The pin is a tight fit in the Mitre table so

that i t will be necessary to turn the table over and

tap the pivot pin home with a light hammer as shown

in fig. 4.

With the pivot pin fully home, screw in the two

locating screws (see fig. 5). Screw them in equally, so

that the carriage is capable of moving evenly and

smoothly on the pivot pin without sloppyness.

2. Feet

Attach the feet to the base at the positions marked

on the underside, using the screws provided.

3. Base

Attach he base to the mitre table using the four hex.

socket screws provided.

4. Work Clamp

Screw the Clamp Support into one of the threaded

holes in the front face of the Mitre Table, (see fig. 6),

depending upon which side of the saw blade your

work is to be mounted, remembering NOT to clamp

the free end of the work.

Secure the Clamp Support with the nut provided

5. Work Stop

Screw the Stop Support rod into the threaded hole at

the end of the Mitre table and lock in place using the

nut provided.

6. Saw Blade

Slide a Depth of Cut Stop on to one of the Guide

Support Rods, (one at each end of the carriage),

before carefully sliding the Blade Guides on to the

Guide Rods. (The stops are secured to the guide rods

at any desired position, to limit the travel of the saw

blade).

Your Mitre Saw is now fully assembled and ready for

use.

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6