Clarus ZF-800 소유자 매뉴얼 - 페이지 8

{카테고리_이름} Clarus ZF-800에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Clarus ZF-800 20 페이지. Treatment systems

페이지 인쇄

Figure 11 - Typical Fusion

WARNING!

CLEANOUT

SEWER LINE

AIR LINES

CONDUIT INSTALLED

BY CONTRACTOR

WHERE APPLICABLE

BLOWER INSTALLATION AND PLACEMENT

1. The blower must be connected to a grounded, metallic, permanent wiring system, or an

equipment-grounding terminal or lead on the product.

2. Place the blower where it is easily accessible for maintenance and inspection.

3. Install the blower in an area where it will be protected from damage and inundation. Also

make certain the location has good ventilation.

4. Install the blower on a foundation that is level and solid.

5. Excavate trenches for two air lines from blower to the unit.

6. Install two separate 1/2" (13 mm) air lines from the blower to the unit. Length of piping

must be less than 17' (5 m). If distances from 17' (5 m) to 33' (10 m) are required, use

3/4" (19 mm) diameter piping (Figure 12). If longer air lines are needed, consult the

factory.

7. The blower is provided with two discharge ports. The blower label is color-coded with the

aeration outlet port being BLUE (main) and the backwash (skim) outlet port being RED

(Figure 12).

8. The air port inlets on the Fusion

backwash (Figure 12).

9. Attach the barbed end of each PVC tee (included in the blower box) to the blower using the

rubber elbows (Figure 12).

10. Attach the small diameter black air tubing (included in the blower box) to barbed fitting

on PVC tee. Black air tubing and blower power cord should be routed to the alarm panel

through conduit. Attach the two black air tubing lines to the two air pressure sensor barbed

fittings in the alarm panel (Figure 12).

11. Connect the remaining end of each PVC tee to the

airlines installed in Step 6.

12. Install the Fusion

blower at an elevation where the

air line outlets are located above the elevation of the

Fusion

air line inlets (Figure 12).

TO PREVENT ELECTRICAL SHOCK

FROM BACK-SIPHONING, LOCATE

THE PUMP ABOVE THE WATER

LEVEL.

Layout

FUSION ALARM PANEL

BLOWER

ALARM FLOAT

OPTIONAL SEPTIC TANK INSTALLATION

MAY BE REQUIRED BY LOCAL

OR STATE REGULATIONS

are also color-coded, BLUE for aeration and RED for

Figure 12

BULK HEAD FITTINGS

FUSION UNIT

AIR LINE FROM PUMP

1/2" SCH 40 PVC

RED AIR

LINE

HIGH WATER FLOAT CONDUIT

TO BE INSTALLED BY

WARNING

HAZARD

ELECTRICAL SHOCK

CONTRACTOR

(WHERE APPLICABLE)

BLUE AIR

LINE

ALARM FLOAT

CONDUIT

AIR SENSOR LINE

RISER AND LID

FUSION

DRILL HOLES FOR

BLOWER MAKE UP AIR

DECORATIVE ROCK CONFIGURATION

INTERIOR CONFIGURATION

BLUE AIR

BLOWER

LINE

POWER

CORD

AIR LINE

TO PANEL

ADAPTER

CONDUIT TO PANEL

SPRING

SEAL AFTER LINE

CLAMPS

INSTALLATION

RUBBER

ELBOWS

AIR LINES

TO PANEL

RED AIR

LINE

BLOWER

GLUE

FITTINGS

1/2 X 3/4 REDUCER

INSTALL BUSHING IF AIR

LINE IS LESS THAN 17'

TO UNIT

TO DISPERSAL

sk2650

DRILL HOLES FOR

BLOWER MAKE UP AIR

DECORATIVE ROCK CONFIGURATION

INTERIOR CONFIGURATION

sk2639