Arnica HydraRain Pro 매뉴얼 - 페이지 17

{카테고리_이름} Arnica HydraRain Pro에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Arnica HydraRain Pro 20 페이지.

페이지 인쇄

4. USE

For effective cleaning, please use the accessories as follows:

•

For carpets, rugs and hard floors, use the combination nozzle B4

with suction hose B3 and suction tube B1.

•

To avoid dust, crumbs etc. from radiators, drawers, cars etc., use

the crevice nozzle B5 to vacuum narrow spaces. Earth, shaving,

crumbs, hair, etc. are sucked up directly with the suction pipe B1

itself.

INSTALLATION FOR DRY SUCTIONS

•

Place rubber caps B2 on the two lower openings on seperator A2

(Fig.8)

•

Fill approx. 2 liters of cold tap water up to the mark on the

suction nozzle into the dirt collecting container A3 (Fig. 9)

•

Place the separator A2 in the dirt container A3. Make sure that

the oval cutout fits correctly. This must be directly above the

suction nozzle (see Fig. 6).

•

Place the motor unit A1 with the buttons directly above the

suction nozzle on the separator A2.

•

Close the two side locks on the (see Fig. 4)

•

Now place the assembled dirt collecting container A3 in the fresh

water container A4. Now close the. Locks on the A5. chassis.

•

Select the. Accessories that. Are most suitable for the work

process. And connect them directly to the pistol grip or attach the

telescopic tube first and then connect the accessories.

•

Now insert the suction hose B3 into the opening of the dirt

collecting container A3 in front of the suction nozzle (Fig. 10)

•

Insert the plug of your vacuum cleaner into the socket and then

press the on/off button to turn your vacuum cleaner off (Fig. 11)

•

After you have finished the vacuuming process, press the on/off

button (Fig. 11) to turn off your vacuum cleaner.

•

After each vacuuming process, empty the dirty water container

A3 and clean it.

ASSEMBLY FOR WET CLEANING

•

Remove the rubber caps B2 from the two lower openings on the

separator A2 (Fig. 12) and place them on the two no-opening

sockets for storage.

•

Take the fresh water tank A4 out of the chassis A5 (Fig. 13).

•

Fill approx. 4 liters of cold tap water into the fresh water tank A4

up to the upper edge of the nozzle (Fig. 14). If necessary, fill in

warm water (up to 60°C).

•

Then place the fresh water tank. A4 on the chassis A5. (Fig. 13).

Make sure it is firmly seated.

•

Connect your suction hose B3 to your Hydra Rain (Fig. 15)

•

For wet floor cleaning, put the suction tube B1 together (Fig. 16)

and insert it into the handle of the suction hose. B3 (Fig.17)

•

Connect the fresh water connection hose to the motor unit A1

and the chassis A5 (Fig. 18).

•

Place the floor suction and spray nozzle B6 on the end of the

pipe. For hard floors with rubber lip B8 (Fig. 19), for. Carpets

slides out rubber lip B8 and put to one side (Fig. 20).

•

For wet cleaning upholstery, attach the upholstery spray and

suction nozzle B7 directly to the handle of the suction hose for

wet cleaning. B3.

•

For optimal and efficient wet cleaning, we recommend. Spraying

the. Surfaces. To be cleaned beforehand and allowing them to

soak for approx. 20 seconds.

•

Just press the PUMP button (Fig. 21) on the device and use the

trigger on the handle to spray water onto the surfaces to be

cleaned.

•

After a short soaking time, switch on the power button and

slowly vacuum the sprayed-in area with the appropriate nozzle

B6 / B7 (for carpets or upholstery)

•

Repeat the process several times until the dirt is completely

removed.

•

If the surfaces are too dirty, let the dirt soak with a cleaning

supplie

CAUTION: Please do not put any cleaning supplies in the fresh

water tank! Regular wet cleaning neutralizes unpleasant odors

in carpets, upholstery and textiles.

Wet cleaning is also recommended for car seats.

5. CLEANING AND MAINTENANCE ATTENTION:

Attention: Always pull the plug out of the socket before

cleaning and mantenance.

•

After each use, empty the water from the fresh water container

A4 and rinse the dirt collecting container A3 with clean water.

Let all parts dry well.

•

Until the fresh water container A4 and the dirt collecting

container A3 are completely dry, please mix your Hydra Rain pro

loosely so that there is enough air to dry the individual parts.

•

For reasons of hygiene and to extend the service life of your Hydra

Rain pro, please never leave liquids and dirt in your device.

•

The HEPA filter in motor unit A1 should be checked regularly for

contamination (Fig. 22). Unscrew the cover of the HEPA filter and