Aroma360 VanGogh360 빠른 시작 매뉴얼
{카테고리_이름} Aroma360 VanGogh360에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Aroma360 VanGogh360 2 페이지.
Aroma360 VanGogh360에 대해서도 마찬가지입니다: 지침 (4 페이지), 지침 (4 페이지), 문제 해결 매뉴얼 (2 페이지)
페이지 인쇄
Adding Your Aroma360 Oil
Be certain the di user is unplugged or powered o before proceeding. Use
the provided key to open the back door. Slide the door up and out to reveal
the oil compartment. You'll notice a tube or nozzle hanging in the
compartment.
2
Pour your oil into the provided aluminum bottle. Then, screw in the aluminum
bottle until it is tightly secured so that the nozzle is in the bottle.
• Do not overfill the bottle.
• Only Aroma360 oils should be used in the VanGogh360; using any other
oils may damage the unit and will void the warranty.
3
Once the bottle of oil is inserted tightly and securely, reattach the door and
lock with the same key. Note: If the bottle is not inserted tightly or straight,
the oil will leak. Please double check that the bottle is inserted correctly.
Once the oil is added, you may turn on or plug in the di user.
4
To remove the bottle from the unit, rotate the bottle counterclockwise until it
comes loose.
5
When changing fragrance oils, remove any oils left in the bottle. (You may
dispose of it or pour it back into the original bottle). Pour some rubbing
alcohol into the aluminum bottle, about ¼ full. Di use the rubbing alcohol for
about 15-30 minutes.
6
Remove any additional rubbing alcohol, rinse and dry the bottle as best as
possible before pouring in the new fragrance oil.
Tips for Using Your VanGogh360
•
The unit must always stay in its upright position. Tilting the di user with oil
inside may cause damage to your unit.
•
Always remove the oil when transporting the unit.
•
If using the di user in a public space, we suggest using the lock feature for
the control panel to prevent tampering with the settings.
There are three ways to use the VanGogh360. As a stand-alone unit, with
the HVAC system or mounted to the wall.
HVAC Connection
Remove the silver nozzle at the top of the unit by unscrewing it counter-
clockwise.
2
Replace it with the External HVAC Connector Nozzle (black part facing up)
and screw it in clockwise and make sure it is tightly secured.
3
Using a screwdriver, make a scent point (a small hole) in the duct work
that is between 0.5-1.5 feet after the air handler. The diameter of the scent
point should be the same as the clear tube that was included with your
Vangogh360+.
4
Insert one end of the clear tube into the External HVAC Connector Nozzle
and the other end into the duct work. To remove the thick tubing from the
di user, simply press down on the black outer portion of the tube connec-
tor and the tubing will release as the black outer ring is a "release" button.
Be sure to cut any excess tubing. Seal the scent point with HVAC tape.
5
Make sure the silver button on the left of the LCD display is out (so that
the fan is switched o ).
6
Attach the power adapter into the unit and plug into a 110v outlet. Program
the Vangogh360 to the desired settings and you're ready to start scenting!
Tips:
Change the fan setting on your thermostat from "Auto" to "Always On" .
Trim any excess clear tubing so that the HVAC tube is as short as possible.
The shorter the tube, the more e icient the scent will be.
Stand-Alone Instructions
Place the unit in an open space with no furniture/fixtures covering or
blocking the unit.
2
Switch the fan on (silver button to the left of the LCD display).
3
Ensure the silver silencer adapter is screwed in to the top of the unit (as
opposed to the HVAC tubing connector.
T R O U B L E S H O O T I N G
PROBLEM
REASON
Power is not getting to the unit or the unit is
No LCD Indication
turned o .
Plug in the unit and press the silver button that is
SOLUTION
on the lower side part of the VanGogh360.
Make sure the unit is plugged in.
No Mist/Scent
Check the LCD display. If it says "OFF", the unit is
not set to be working at that time. If the unit says
"PAUSE" it's on the pause portion of the interval.
Oil could be out.
Ensure the power is connected and adjust the
event times and days so that the unit is set to
SOLUTION
"ON". Also check the oil canister to make sure
there is oil in the bottle.
Low Mist/Scent
The nozzle may be clogged.
Run with rubbing alcohol for three minutes or
SOLUTION
change the nozzle.
The VanGogh360 may be tilted.
Oil Leakage
Your oil bottle may not be secure.
Ensure the VanGogh360 is in a full and upright
position.
SOLUTION
Remove the fragrance bottle and reattach making
sure it is screwed in straight and is very tight.
The unit's settings may be locked.
Buttons are not
working
Hold down the SET button for 10 seconds until you
SOLUTION
hear a beep. The sound will indicate "lock mode"
has been disabled.
T h e
V A N G O G H 3 6 0
Through the advanced technology of Cold-Air Diffusion,
your discreet and sleek Aroma360 diffuser is a convenient
and practical solution to enhance any space you desire.