CAME Z Series 매뉴얼 - 페이지 3

{카테고리_이름} CAME Z Series에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. CAME Z Series 4 페이지. Control board
CAME Z Series에 대해서도 마찬가지입니다: 매뉴얼 (8 페이지), 매뉴얼 (20 페이지), 매뉴얼 (4 페이지), 매뉴얼 (17 페이지), 매뉴얼 (17 페이지), 매뉴얼 (13 페이지), 매뉴얼 (13 페이지), 매뉴얼 (16 페이지), 매뉴얼 (16 페이지), 매뉴얼 (12 페이지), 매뉴얼 (12 페이지), 매뉴얼 (18 페이지), 설치 매뉴얼 (11 페이지), 매뉴얼 (8 페이지), 매뉴얼 (20 페이지), 매뉴얼 (12 페이지), 매뉴얼 (12 페이지), 기술 문서 매뉴얼 (16 페이지), 사용 설명서 (16 페이지), 지침 (4 페이지), 빠른 매뉴얼 (2 페이지), 연결 매뉴얼 (4 페이지), 매뉴얼 (4 페이지), 매뉴얼 (12 페이지), 매뉴얼 (20 페이지), 매뉴얼 (15 페이지), 사용 설명서 (12 페이지), 빠른 시작 매뉴얼 (12 페이지), 매뉴얼 (16 페이지)

페이지 인쇄

COMMISSIONING

The system must be wired fully. Turn 5 6 & 7

fully anticlockwise, then 5 & 7 clockwise by

. Set the transformer torque to position 1.

Follow commissioning route from

FROG systems, read guide T6 for setting the

motor direction.

Mains in

L1 L2

MAIN COMPONENTS

Connectors

Mains fuses, 5A

Accessory fuse, 1.6A

Programme button

Run time adjustment

Interleaf delay

Open period

Programme DIP's

Radio head plug

10. Indicator LED

11. Torque setting

Capacitor cables

12.

www.came.co.uk

RADIO CODE SETTING

The AF43 radio head plugs onto the

ZA4 board at 9 . Ensure the jumper is

set correctly on both pins. See below:

c5.

RECEIVER SETTING

The ZA4 holds the radio code in flash

memory. To set a code, press & hold

prog button 4 . The red LED 10 will

flash. Now press the radio transmitter

button as well. The LED will light con-

stantly until both buttons are released.

Motor Connector

U V W X Y E1

TORQUE SETTING

The power of the motor is set on the

transformer. A black wire connects to

the transformer in one of 4 positions

by a white fast-on connector. Select

the lowest setting (

ensure reliable satisfactory operation.

RUN TIME SETTING

The motor running time is set by 'TL'

(

adjustment 5

with the longest travel arrives 2 secs

before the motor switches off. Run

time is less important on motors with

limit switches. The overrun time will

be added to the open period.

Helpline Tel: 0870 012 9000

Control Connector

10 11 1 2 3 5 7 C1

) that will

from 1 to 4

). Set such that the motor

TRANSMITTERS

The TOP432s code is set on switches

inside the transmitter. We recommend

changing the code from that supplied.

To copy a code to a new transmitter,

set the switches until they match.

1- Hold prog button

2- Press transmit

3- Let go both

Aerial

INTERLEAF DELAY

This allows overlapping gate leaves

to close in the right order by applying

a delay before closing motor 2 (

AUTOMATIC CLOSING

Auto-closing is enabled by switching

DIP 2 on (up) on switch block 8. The

gates re-close from 1 to 60 sec after

opening. The open period is set on 7.

The LED indicator flashes once per

second during the open period.

Changes should be made by competent

persons only. Always disconnect power

before making any wiring changes.

)

WXY

- 3 -